A 10:1 divider with 12.8 pF across its top resistor
Drawn above at its default parameters, which is almost never how an essay calls it. A placement states the numbers that essay is arguing about, so the figure a reader meets is about that argument rather than about the generator — 98% of the placements on this site pass one, and the phase that raised that number from 12% found eight captions describing a figure the page was not showing.
At those defaults the edge it states is 0.0% out at 12.8 pF — the right-hand slot
of the caption strip, which on this site is never used for anything else, and which is read
back out of the drawing above rather than out of the code that wrote it.
It belongs to Measurement, which is a circuit on a circuit, which is to say a change to it is a
change to lib/figures/instruments.js.
It takes a slider on trimmer capacitance (picofarads) with 7 settings,
and every one of them has passed the same assertions as the frame above — a figure whose
circuit stops doing what its caption says at any setting stops the build.
Called by 5 essays
which is the blast radius of changing it
A divider with two ratios
Put capacitance in a resistive divider and it divides by resistance at direct current and by capacitance at high frequency, and those are two different numbers unless one equation holds. The adjustable trimmer on every oscilloscope probe exists for that single equation, and the square wave on the instrument's front panel is a display of which of the two ratios is currently winning.
The probe that takes a tenth
A ten-to-one probe buys an order of bandwidth for a tenth of the signal, and on a two-kilohm source the bandwidth is exact: 6.79 kHz becomes 69.2 kHz. The tenth of the signal is not a tenth of the signal-to-noise ratio. Solved resistor by resistor, the noise referred to the tip goes from 1.782 µV to 55.78 µV — a factor of 31.3 — because the divider that does the attenuating is nine megohms and a megohm, and √(n(n−1)kT/C) on the cable's own capacitance has no source resistance in it at all.
The time constant one trimmer cannot reach
A ten-to-one divider whose lower arm is 100 pF of instrument input and 15 pF more reached through a kilohm reads flat on a 1 kHz calibrator with its trimmer at 12.8 pF — the same setting as a lower arm of 115 pF lumped — and overshoots 12.8% on a 1 ns edge, settling within 1% only after 35.5 ns. No setting of the one trimmer is flat: the best judged on a fast edge is 6.1%, at 11.9 pF, and a trimmer set by eye so the fast edge lands flat leaves the calibrator's square wave 9.9% low with a 114 µs slope on its top. Flat at every time needs the upper arm to be a scaled copy of the lower one — a second branch of 9 kΩ and 1.7 pF — and then a 1 ns edge is flat to 10⁻¹⁰, with a window of −18 to +24% on that resistor and ±6% on its capacitor.
The source the hook hides behind
A compensated divider with a late branch in its lower arm overshoots 13.2 per cent on an ideal step, and every measurement of that hook has been made from a source with no resistance. Through a real source the input capacitance charges first, and the hook and the source's lag act on the same edge. The overshoot is 10.5 per cent from 50 Ω, 4.13 from 300 Ω and gone by a kilohm, where the source's lag equals the hook's. The excess has not gone away: it is in the edge, which the screen shows 15 per cent faster than the source and the probe's capacitance allow. And the second branch that made the divider exact only makes its ratio exact, so from a kilohm the exact divider settles in 65.6 ns and the one with the hook in 44.
The branches a square root needs
A resistive cable's late charge is a continuum and not one branch, and the partial fractions of its tanh are an exact description of it: 81.1 per cent of the capacitance behind a time constant of 12.2 ns, 9.01 per cent behind a ninth of that, 3.24 behind a twenty-fifth, all through the same kilohm. So a divider's upper arm can copy it one piece at a time. On a 1 ns edge one trimmer alone is 11.2 per cent out, one copied branch 1.07, two 0.252 and four 0.0353. The first branch does most of the work and the uncopied capacitance falls only as one over the count; what saves the rest is that a branch faster than the edge is averaged away. Faster edges ask for more branches, and the tolerance on the first ends the series before the arithmetic does.