A resonator's Q against its inductor's, with a capacitor of Q 1581
Drawn above at its default parameters, which is almost never how an essay calls it. A placement states the numbers that essay is arguing about, so the figure a reader meets is about that argument rather than about the generator — 98% of the placements on this site pass one, and the phase that raised that number from 12% found eight captions describing a figure the page was not showing.
At those defaults the edge it states is Q 75.3 under a ceiling of 79.1 — the right-hand slot
of the caption strip, which on this site is never used for anything else, and which is read
back out of the drawing above rather than out of the code that wrote it.
It belongs to Frequency, which is the same solve, which is to say a change to it is a
change to lib/figures/frequency.js.
It takes a slider on the coil's series resistance (ohms) with 6 settings,
and every one of them has passed the same assertions as the frame above — a figure whose
circuit stops doing what its caption says at any setting stops the build.
Called by 8 essays
which is the blast radius of changing it
The Q the components allow
Resonance and its bandwidth measured a half-power width of exactly f₀/Q at every Q tried, for a circuit whose only resistance was the one deliberately put there. Real components arrive with resistance of their own, and the consequence is a ceiling rather than a penalty. The reciprocals of the component quality factors add, so the total sits below the smallest of them: an inductor of 79 beside a capacitor of 1 581 gives a resonator of 75. The worst component decides and the best one cannot help.
The same part written two ways
A capacitor's loss is quoted either as a resistance in series with it or as one across it, and the pair of expressions that converts between them is exact at one frequency and at no other. How wide the band is around that frequency is set entirely by the quality factor: an octave and a half at Q of eight, a thousand to one at Q of three thousand.
The resistor that is only a resistor
A capacitor becomes an inductor above a frequency its leads decide, and an inductor becomes a capacitor. The third member of that family is the one nobody draws, and it is the only one whose edge is not monotonic in its own value: a ten-megohm resistor stops being one at 19 kilohertz, a ten-ohm resistor at 92 megahertz, and between them sits a resistance whose impedance is flat to fourth order — 91.02 ohms here, which is the square root of L over C divided by the root of one plus root two.
What actually fills a null
A ten per cent error in the two components of a notch's arm leaves the null three hundred decibels deep — it moves it rather than filling it. What fills it is loss, at twenty decibels per decade of arm resistance exactly. And the depth at the frequency the notch was designed for splits into two orders depending on which way the two errors go: one per cent parts leave 79 decibels one way and 33 the other.
The band that does not close
A cascade of active sections can be built at three decades of impedance level at second order, one at sixth, and none at all at eighth — the band shuts by half a decade per order because two fixed quantities bind it from opposite ends. A doubly terminated ladder has only one of those quantities, because an inductor's loss is a fixed quality factor rather than a fixed resistance and therefore scales with the design. At order nine it still has four decades.
Two parasitics, and the resonance neither of them has
A resonator's quality factor is supposed to sit below the worst of its components, because reciprocals add. Give the capacitor half a millihenry of its own inductance and the loop measures 92.21 against a coil that allows 64.55 and a reciprocal sum that predicts 62.47 — the ceiling passed exactly where ESL/L crosses ESR/DCR, at 5.00 per cent. Add the coil's own capacitance beside it and the loop grows a second resonance at 28.2 kHz that neither part has alone, taller than the first by 40.4, and the half-power level is then crossed four times.
The match with no knob
An L-section — a series inductor and a shunt capacitor — is the series–parallel conversion used on purpose: a load with a capacitor across it is, at one frequency, the source's resistance in series with a reactance an inductor cancels. Matching fifty ohms to a kilohm that way reflects 3.6 × 10⁻¹⁶ at its design frequency and has a Q of √19 = 4.359 that no choice of parts can change, so it holds its reflection under a tenth over 4.73 per cent of band whatever it is built from. The band is 0.2/Q to within three per cent, it depends on nothing but the ratio, and only splitting the match widens it: 14.98 per cent in two sections, 30.34 in three — and 30.83 in four.
The efficiency a fixed Q costs
An L-section's quality factor is √(ratio − 1) with nothing left to choose, and the same fixed Q that decides its band decides what it dissipates. The circulating current is Q times the load's and it goes through both components, so the loss is twice Qₛ over the components' own Q — measured to 0.03 per cent. With parts of Q 100 that is one per cent at a resistance ratio of 1.253, which is fifty ohms to sixty-three. And splitting the match buys efficiency only above a ratio of 10.02: below it a second section adds two more lossy parts for less than it takes off anybody's Q.