A follower's output impedance from 1 kΩ of source, bare and with 100 pF on it
Drawn above at its default parameters, which is almost never how an essay calls it. A placement states the numbers that essay is arguing about, so the figure a reader meets is about that argument rather than about the generator — 98% of the placements on this site pass one, and the phase that raised that number from 12% found eight captions describing a figure the page was not showing.
At those defaults the edge it states is 3.5× its own low-frequency value at 29.3 MHz — the right-hand slot
of the caption strip, which on this site is never used for anything else, and which is read
back out of the drawing above rather than out of the code that wrote it.
It belongs to Devices, and where they stop being linear, which is to say a change to it is a
change to lib/figures/semi.js.
It takes a slider on source resistance (ohms) with 7 settings,
and every one of them has passed the same assertions as the frame above — a figure whose
circuit stops doing what its caption says at any setting stops the build.
Called by 5 essays
which is the blast radius of changing it
The buffer that is not a buffer
An emitter follower is reached for when something has to be driven without being loaded: unity gain in, high impedance seen, low impedance presented. The last of those is a number with a range, and the range is narrow. At a kilohm of source the emitter presents 19.08 ohms at low frequency and 67 ohms at 29 megahertz, because the current gain that made it small is falling — and the peak is worst in the middle of the slider, so it cannot be avoided by making the source stiffer or softer.
The input that pushes back
An emitter follower with a capacitor on its emitter has a negative resistance looking into its base — 1182 ohms of it at 3.4 megahertz for a nanofarad, with nothing added to the model. A negative resistance is not an oscillator until a reactance cancels, and the base lead supplies it: with ten ohms of source the loop goes unstable above 74.9 nanohenries, which is seven centimetres of wire. The repair is the opposite of the instinct — a hundred ohms of source raises the threshold to 913 nanohenries, so the fix for a follower that oscillates is to make the thing driving it worse.
The resistance that is below zero
An emitter follower's output resistance is 5.5 Ω at direct current and −21.9 Ω at 257 MHz, and the sign is not the transistor's: with an ideal source at the base there is no negative band at all, and a hundred nanohenries of wire between the source and the base produces one from 110 to 301 MHz. A capacitance resonating inside that band is a resonator with loss of the wrong sign, so 4.7 to 100 pF on the emitter oscillates while 1 pF and 470 pF do not — a band of load capacitance with quiet ground on both sides of it.
What the cure at the base costs
Bisecting for the smallest base resistor that stops an emitter follower oscillating gives 8 to 79 ohms. That bisection stops at the sign change, so at the value it returns the pole pair sits on the imaginary axis with a real part of 10⁻⁷ per second and a quality factor of 1.7 × 10¹⁵ — stable, and undamped. A quality factor of one needs 1.15 kΩ at 47 pF, sixteen times more, and that resistor takes the output impedance from 5.66 to 13.10 ohms. The other cure the model has always accepted and nothing has ever used is a resistor at the emitter: it reaches the same damping with 5.68 ohms and costs half the signal.
The follower that lets go on the way down
An emitter follower can push current into its load without limit and pull it out only through whatever sinks the emitter. Marched as a large-signal circuit — a 2 mA sink, 1 nF on the emitter — a 1 V, 1 MHz sine asks the output to fall at up to 6.28 V/µs, the sink allows 2.00, and on every falling stretch the junction reverse-biases, the emitter current drops below a hundredth of its quiescent value for 57% of the cycle, and the output falls as a straight line of exactly −I/C. The boundary is a slope, 2πfA ≤ I/C: 2.87 V at 100 kHz, 0.309 V at 1 MHz, creeping above the line only as the period approaches the junction's own 12.9 ns. Past it the follower rectifies — its output's average rises 415 mV at 1 V of drive and 1.30 V at 2 V — and with a resistor in place of the sink the fall slows as the output descends, from 2.41 V/µs to 1.99. None of it is visible to the small-signal model the earlier essays used.