One exponential and one pair, both driven 20.0 mV
Drawn above at its default parameters, which is almost never how an essay calls it. A placement states the numbers that essay is arguing about, so the figure a reader meets is about that argument rather than about the generator — 98% of the placements on this site pass one, and the phase that raised that number from 12% found eight captions describing a figure the page was not showing.
At those defaults the edge it states is the pair's second harmonic is 1e-16 — the right-hand slot
of the caption strip, which on this site is never used for anything else, and which is read
back out of the drawing above rather than out of the code that wrote it.
It belongs to Devices, and where they stop being linear, which is to say a change to it is a
change to lib/figures/semi.js.
It takes a slider on drive amplitude (volts) with 7 settings,
and every one of them has passed the same assertions as the frame above — a figure whose
circuit stops doing what its caption says at any setting stops the build.
Called by 7 essays
which is the blast radius of changing it
What a pair cancels, and what it only halves
A differential pair's transfer characteristic is an odd function, and an odd function driven symmetrically produces no even harmonics at all. Measured, the second harmonic comes out at 10⁻¹⁶ of the fundamental — the arithmetic's own floor, not a small physical residue. The third harmonic is a different story, and it comes out at exactly half the single stage's, which is a reduction and not a cancellation.
What the limiter charges for
The diodes that set the amplitude are the only nonlinear thing in the loop, so every harmonic in the output is theirs. Across the gain slider the amplitude rises by a factor of 1.51 and the distortion by 15.4 — an amplitude that goes as the 0.11 power of the excess gain and a distortion that goes as the 0.74 power. Two diodes facing opposite ways produce no even harmonic at all, at seven parts in ten million, which is the arithmetic's floor rather than a small residue.
The rejection the parts have
Two essays measured the architecture: four resistors decide an instrumentation amplifier's rejection, two do not, and the answer is the one-amplifier figure plus twenty log of the first stage's gain — exactly, with amplifiers of infinite rejection. Give each amplifier its own and something unobvious happens: two matched but individually mediocre parts cost nothing at all, because their error is a common-mode signal at the difference stage and is rejected there. What costs is the difference between them, and it sets a ceiling with no gain in it.
Where the two exponents come from
What a resistor in the emitter buys measured two exponents and could explain neither: the distortion edge moves as the square of the degeneration factor and the gain edge as its 0.950 power, and at a factor of exactly three halves the gain error vanished. The degenerated transfer curve has no closed form forwards and an exact one backwards, and reverting that series gives all three. The distortion exponent is exactly two; the gain edge is proportional to D squared over the root of the absolute value of three minus twice D, which is infinite at three halves and tends to a three-halves power; and the two edges are 7.07 apart on the bare device and 1.62 at a factor of eleven, against 7.06 and 1.61 measured.
The point the device is never at
A device's linearity is specified by one number, and that number is a place on no curve. The third-order intercept is where two straight lines would cross if both went on being straight, and neither does. For a differential pair the crossing sits π²/4 — 7.84 decibels — above the largest output the device can produce at any drive whatever, and the arithmetic that says so contains no tail current and no temperature.
The step too large to have an impedance
The rung below drove the load node with a current step and reported an impedance: a voltage divided by a current, which is a number only if the ratio does not depend on the current. Give the amplifier the differential pair's own tanh in place of a linear transconductor and it is a number up to 10.6 milliamps and not above — where the input error is 3.63 thermal voltages, and where the slew rate that decides it is twice the thermal voltage times the gain-bandwidth in radians, containing no design choice at all.
The product that is not the third
Every distortion result in this field is odd-order, and the two-tone machinery has computed the second-order product on every call since the day it was written and thrown it away. On a bare exponential it is the drive over twice the thermal voltage — 1.934 × 10⁻² of the fundamental at a millivolt, against 1.870 × 10⁻⁴ for the third-order product, a ratio of 4Vₜ/a and a hundred and three to one. A differential pair puts it at 6.2 × 10⁻¹⁶. And degeneration removes it as D⁻² where it removes the third order as D⁴/|3 − 2D|, so a stage linearised until its third-order product is negligible is a stage whose distortion is almost entirely the one nobody measured.