The millivolts in the wire, which are nobody's signal
Drawn above at its default parameters, which is almost never how an essay calls it. A placement states the numbers that essay is arguing about, so the figure a reader meets is about that argument rather than about the generator — 98% of the placements on this site pass one, and the phase that raised that number from 12% found eight captions describing a figure the page was not showing.
At those defaults the edge it states is the signal is lost by 1.59 MHz — the right-hand slot
of the caption strip, which on this site is never used for anything else, and which is read
back out of the drawing above rather than out of the code that wrote it.
It belongs to Measurement, which is a circuit on a circuit, which is to say a change to it is a
change to lib/figures/instruments.js.
It takes a slider on length of the shared return (millimetres) with 6 settings,
and every one of them has passed the same assertions as the frame above — a figure whose
circuit stops doing what its caption says at any setting stops the build.
Called by 7 essays
which is the blast radius of changing it
The millivolts in the wire
Ten millimetres of one-ounce copper is five milliohms and ten nanohenries, and if a hundred-milliamp load and a ten-millivolt sensor both return through it, half a millivolt of somebody else's current is added to the reading — five per cent of it, before anything has been amplified. Above 79.6 kilohertz the error rises a decade per decade with no ceiling, and shortening the shared run moves the whole curve down and the corner not at all.
The rejection four resistors decide
Measuring a ten-millivolt sensor against a ground that somebody else's hundred milliamps is also using puts five hundred microvolts of their current into the reading. Subtracting the two ends of that conductor with a difference amplifier removes it — by 53.99 decibels with one-tenth-per-cent resistors, against a closed form of 53.98, which is a factor of five hundred and not a removal. The amplifier has nothing to do with it: the number is one plus the gain over four times the resistor tolerance.
The ammeter that is a resistor
Every direct measurement of a current is a measurement of a voltage across something the current was made to flow through, so the instrument has two errors pointing opposite ways: a larger shunt changes the current, a smaller one leaves less for the amplifier's offset to be compared with. Written in the burden voltage they are the burden over the supply and the amplifier's offset over the burden, and the best of them is at the geometric mean — 7.75 millivolts on a twelve-volt rail, with a worst-case error of 0.129 per cent. Neither number contains a resistance, and neither contains the current: ten milliamps and a hundred amps want the same 7.75 millivolts.
The corner the instrument has no part in
Three earlier essays measured a three-amplifier instrumentation amplifier's rejection at direct current and found 95 dB, of which the resistors' matching decides one part and the amplifiers' own mismatch another. Connect it to a source with a kilohm of imbalance and ten picofarads at each input and the rejection has a corner at 290 Hz and falls twenty decibels a decade after it — reaching 84 dB at a kilohertz on an instrument that is still doing 95. What converts common mode to differential is the difference of two time constants, and the cure is a capacitor on the quiet input.
Every tooth the same height
A shared return conductor's impedance rises a decade per decade above 79.6 kilohertz and a switching load's harmonics fall a decade per decade, so the two cancel exactly: every harmonic of a hundred-milliamp square wave puts 0.828 millivolts into a ten-millivolt reading, from the conductor's own corner up to the edge's. The comb is flat rather than falling, so the total is decided by how many teeth there are — and since they add in quadrature it grows as the square root of the edge rate, 39.7 millivolts at a nanosecond against 4.03 at a hundred.
One voltage added to two readings
A difference amplifier across a shared return rejects somebody else's current by 54 decibels, and the number is four resistors rather than the amplifier. Two sensors referenced to the same node do better by a different mechanism entirely: the interfering voltage is one voltage on one node, so it is added to both readings identically and the difference between them has none of it — 511 microvolts in each reading against two and a half picovolts in the difference, which is 166 decibels and is exact rather than good. What is left is not a tolerance but a mismatch between the two sensors' own return paths, ten nanovolts per per cent of it.
A star is half a millimetre long
The repair for a shared return is a star ground, and it is described as making the shared length zero. It does not: every return meets at a pad, the pad reaches the plane through a via, and a via of a quarter-milliohm and 0.35 nanohenries is worth half a millimetre of one-ounce track by its resistance and 0.35 by its inductance — two different lengths, so a via has a corner of its own at 114 kilohertz where a track's is at 79.6. What that buys is a change of law rather than a factor: a daisy chain's error grows as the square of the circuit count and a star's as the first power, so the advantage runs from sixty times at two circuits to three hundred and forty at thirty-two.