Circuit Response
every model has an edge, and the figure carries it
Series

Common-impedance — the series

4 essays on one idea, from the one that introduces it to the one that assumes the rest.
  1. The millivolts in the wire, which are nobody's signal. computed by solving, not by drawing at 145 frequencies. A 10 mm run of one-ounce copper carries the return of a 100 mA load and the reference of a 10 mV sensor. Its 5.00 mΩ and 10.0 nH put 500.0 µV in series with the sensor at low frequency — 5.00% of the reading — rising a decade per decade above 79.6 kHz until at 1.59 MHz the error is the whole signal. The full solve and the interfering current times the shared impedance agree to 4.4e-7. The slider is the length of the shared run: both the resistance and the inductance are proportional to it, so every point on the curve moves down together and the corner stays at 79.6 kHz.

    The millivolts in the wire

    Ten millimetres of one-ounce copper is five milliohms and ten nanohenries, and if a hundred-milliamp load and a ten-millivolt sensor both return through it, half a millivolt of somebody else's current is added to the reading — five per cent of it, before anything has been amplified. Above 79.6 kilohertz the error rises a decade per decade with no ceiling, and shortening the shared run moves the whole curve down and the corner not at all.

    part 1 · instruments
  2. A switching load's comb in a 10 mV reading: every tooth the same height. computed by solving, not by drawing. The harmonics of a 50-per-cent trapezoid of 100 mA at 100 kHz with a 10 ns edge, each multiplied by the shared conductor's impedance at its own frequency. Below 79.6 kHz the conductor is 5.00 mΩ of resistance and the teeth fall as 1/n. Above it the conductor rises as n while the harmonics still fall as 1/n, so the two cancel and every tooth from 239 kHz to 10.6 MHz is 0.828 mV — flat to 5.4 per cent across 52 of them. The comb stops at 31.8 MHz, which is the edge's own corner, so the total of 12.6 mV is decided by how many teeth there are: fitted over five edge rates it grows as the edge time to the power -0.497, against the −½ that a quadrature sum of equal teeth gives. A faster edge raises no harmonic and adds teeth. What a slow measurement keeps is a different term entirely: the zeroth harmonic, which is the 100 mA average through 5.00 mΩ of resistance — 500.0 µV, with no inductance in it and no edge, against the comb's 12.6 mV.

    Every tooth the same height

    A shared return conductor's impedance rises a decade per decade above 79.6 kilohertz and a switching load's harmonics fall a decade per decade, so the two cancel exactly: every harmonic of a hundred-milliamp square wave puts 0.828 millivolts into a ten-millivolt reading, from the conductor's own corner up to the edge's. The comb is flat rather than falling, so the total is decided by how many teeth there are — and since they add in quadrature it grows as the square root of the edge rate, 39.7 millivolts at a nanosecond against 4.03 at a hundred.

    part 2 · instruments
  3. Two sensors on one return: 511 µV in each reading, 100 nV in the difference. computed by solving, not by drawing. Two sensors referenced to the same local node, each reaching it through 2 mm of its own copper and each drawing 1 mA through that copper, with a 100 mA load returning through the 10 mm they all share. The interfering voltage is one voltage on one node, so it is added to both readings identically and the difference between them has none of it: 511.0 µV in each reading against 100.0 nV in the difference at a kilohertz, which is 74.2 dB. No resistor tolerance enters it — with the two stubs equal the rejection is exact to the solver, 166 decibels. What is left is the 10 per cent MISMATCH between the stubs times the sensors' own current, which the closed form puts at 100.0 nV, and it is proportional to the mismatch: 10.0 nV at 1%, 30.0 nV at 3%, 100 nV at 10%, 300 nV at 30%.

    One voltage added to two readings

    A difference amplifier across a shared return rejects somebody else's current by 54 decibels, and the number is four resistors rather than the amplifier. Two sensors referenced to the same node do better by a different mechanism entirely: the interfering voltage is one voltage on one node, so it is added to both readings identically and the difference between them has none of it — 511 microvolts in each reading against two and a half picovolts in the difference, which is 166 decibels and is exact rather than good. What is left is not a tolerance but a mismatch between the two sensors' own return paths, ten nanovolts per per cent of it.

    part 3 · instruments
  4. A star ground is a 0.50 mm daisy chain, not a point. computed by solving, not by drawing. 8 circuits of 100 mA each meeting at one pad, which reaches the plane through a via of 0.25 mΩ and 0.35 nH. The via is shared by every one of them, so the star's residual is 7 other currents through it — 175.0 µV at 1.00 kHz against the 1.800e+4 µV a daisy chain of 10 mm hops would give at its far end, a factor of 103. Measured as a length of the same track, the via's resistance is worth 0.500 mm and its inductance 0.350 mm — two different lengths, so a via has a corner of its own at 114 kHz where a track's is at 79.6 kHz wherever it is cut. The faint curves are other circuit counts. The two grow differently: fitted over counts from 2 to 32 the star's error goes as N^1.22 and the chain's as N^1.87, because a chain's hop carries every circuit beyond it — so the star's advantage grows with the count rather than shrinking. And a star has no position in it: a chain's far end reads 4.5 times its near end, which is a diagnostic no real fault should have.

    A star is half a millimetre long

    The repair for a shared return is a star ground, and it is described as making the shared length zero. It does not: every return meets at a pad, the pad reaches the plane through a via, and a via of a quarter-milliohm and 0.35 nanohenries is worth half a millimetre of one-ounce track by its resistance and 0.35 by its inductance — two different lengths, so a via has a corner of its own at 114 kilohertz where a track's is at 79.6. What that buys is a change of law rather than a factor: a daisy chain's error grows as the square of the circuit count and a star's as the first power, so the advantage runs from sixty times at two circuits to three hundred and forty at thirty-two.

    part 4 · instruments

All series