Circuit Response
every model has an edge, and the figure carries it
Series

Q enhancement — the series

4 essays on one idea, from the one that introduces it to the one that assumes the rest.
  1. An amplifier a hundred times the corner moves the unity-gain section's Q by 2.0%. computed by solving, not by drawing. A unity-gain Sallen–Key section designed for Q = 2 at 1.00 kHz, built with a one-pole amplifier, and its poles recovered by rooting the determinant. The section as drawn has two poles; as built it has three, and the pair is not where it was put. At a gain-bandwidth of a hundred times the corner — which is the rule of thumb — the quality factor is 1.97 per cent high and the pole frequency is 1.97 per cent low. The two are the same number with opposite signs over the window where the amplifier is well clear of the section and its own pole is still resolvable, and the number is the designed quality factor, 2, divided by the ratio: 2.00 per cent at 100 times the corner.

    The Q the amplifier decides

    A second-order section's quality factor is set by a capacitance ratio and its pole frequency by a product of four passive values, and neither expression contains the amplifier. Build it with one that has a gain-bandwidth a hundred times the corner — the usual rule — and the Q comes out 1.97 per cent high while the pole comes out 1.97 per cent low, the same number in both directions, and the number is the designed Q divided by the ratio. A fifth-order half-decibel Chebyshev built that way has 2.1 decibels of ripple.

    part 1 · filters
  2. A half-decibel filter that meets one decibel at 25 °C and does not at 89. computed by solving, not by drawing. The passband ripple of a fifth-order 0.5 dB Chebyshev built from three Sallen–Key sections, against temperature, with a part whose gain-bandwidth at 300 K is 300 kHz against a 1 kHz corner. Not one passive component has a temperature coefficient in this model. The ripple is 0.824 dB at −40 °C and 1.049 at +125, and it crosses a one-decibel specification at 88.6 °C — a boundary in temperature, which every other edge in this collection is not. The dashed line is the same filter with a tail current proportional to absolute temperature: 0.916 dB at both ends, and no crossing anywhere.

    The ripple that is a temperature

    An amplifier a hundred times the corner leaves a section's quality factor two per cent high. That two per cent has a temperature in it: with a tail current a resistor sets, the transconductance falls as one over absolute temperature, and a fifth-order half-decibel design whose passives have no temperature coefficient at all goes from 0.82 decibels of ripple at minus forty to 1.05 at a hundred and twenty-five — crossing a one-decibel specification at 89 °C. With the other bias it does not move at all.

    part 2 · filters
  3. At Q = 2 and a hundred times the corner, one arrangement is 1.97% out and the other 2.83%. computed by solving, not by drawing. The same second-order section designed twice — a follower with a capacitance ratio, and equal passives with the Q supplied by a closed-loop gain of 2.5000 — built with the same one-pole amplifier and swept over its gain-bandwidth, with both pole pairs recovered by rooting the determinant. The unity-gain arrangement's error is Q over the ratio: 2.00 per cent at a hundred times the corner. The equal-component arrangement's is K²/2 over the ratio, 3.13 per cent, because its amplifier is a gain-of-K stage and therefore has K times less bandwidth to spend. Below about thirty times the corner both laws fail, and the second one changes sign.

    Where the Q comes from

    Two second-order sections with no component value in common have the same transfer function to 1.8×10⁻¹⁰ of a decibel, and are not the same circuit. Against a slow amplifier the follower's Q error is Q over the gain-bandwidth ratio and the gain stage's is K²/2 over it — so the second is worse below Q = 3.08 and better above it. Against component tolerance the follower's worst element carries ½ and the gain stage's carries 2Q − ½, nineteen times as much at Q = 5. Neither oscillates at any gain-bandwidth at all.

    part 3 · filters
  4. A follower section of Q = 5 on an amplifier 100 times the corner: +4.79% as designed from the formula; designed for that amplifier, exact at it, and +1.64% and −0.966% on parts 30% slow and fast. computed by solving, not by drawing: the realised Q of a unity-gain Sallen–Key section against the actual amplifier's gain–bandwidth, relative to the typical value it was chosen for, from the poles of the netlist. Designed from the textbook formula (solid): +6.51% at 0.7, +4.79% at 1, +3.78% at 1.3. Predistorted, with its capacitance ratio and resistors found by iteration on the netlist so that the typical part is exact (dashed): +1.64% at 0.7, exact at 1, −0.966% at 1.3. Predistortion moves the line down without changing its slope much: it removes the error the amplifier has in common and leaves what differs between amplifiers.

    The Q designed for the amplifier

    A follower section's Q comes out 4.79 per cent high at Q = 5 with an amplifier a hundred times the corner, and nothing stops a designer asking for 4.771 so that the real circuit lands on 5.000. That removes the error the amplifier has in common and leaves what differs between amplifiers: parts 30 per cent slow and fast read +1.64 and −0.97 per cent. So the exchange rate is the spread itself, and it is large. One per cent of Q across ±30 per cent asks for 725 times the corner from the formula and 196 designed for the part. The design runs out at a definite ratio, 7.2 times at Q = 5, below which no value of its parts reaches the Q wanted. On a whole Chebyshev 5 the passband error falls from 1.43 dB to nothing on a typical part and 0.55 on a slow one.

    part 4 · filters

All series