Circuit Response
every model has an edge, and the figure carries it
Series

Asymptotic approximation — the series

5 essays on one idea, from the one that introduces it to the one that assumes the rest.
  1. A pair at Q = 0.7071: the sketch is -3.01 dB out at the corner. computed by solving, not by drawing. The solved magnitude against the two straight lines that stand in for it. At a conjugate pair the error at the corner is 20 log Q = -3.010 dB, which is unbounded in both directions, and the worst error anywhere is 3.010 dB at 1.00× the corner. No damping brings it inside 0.770 dB: that is the minimax, at Q = 0.9152, where the corner error and an interior maximum are equal.

    The straight lines, and where they are not the curve

    Two straight lines through a corner is the most-used approximation in this subject and almost the only one with no number attached. It has one, and it is exact: at a single real pole the sketch is 3.0103 decibels high at the corner and nowhere worse, and its error is the same a factor above the corner as the same factor below — a symmetry the construction does not suggest. A pole pair has no such bound at all, and the best any two-slope sketch can do on one is 0.770 decibels, at a quality factor of 0.9152.

    part 1 · frequency
  2. The straight lines report 45.00° of margin, and the solved loop has 51.83°. computed by solving, not by drawing. The gain and phase of a loop made of an integrator and one pole, the corner at 1.00 kHz, with the integrator set so that the straight-line asymptotes cross unity at 1.00 kHz. The solved loop crosses at 786 Hz instead. Read at the lines' crossover, with the phase taken from the solve, the margin is 45.00°; at the loop's own crossover it is 51.83°. Closed, the loop is stable: the largest real part among its closed-loop poles is -5.00e-1 of the corner's angular frequency. The solved gain never rises above its asymptotes, so the lines cannot report more margin than the loop has.

    The margin the straight lines report

    A phase margin read off a sketch is read where the straight lines cross unity, and that is not where the loop does. For an integrator and one real pole the lines report 45.00 degrees on a loop that has 51.83 — short, and always short, because a real pole's response never rises above its asymptotes. A pair that peaks reverses the sign and removes the bound: at a quality factor of two the lines report 71.57 degrees on a loop that has no margin at all, and at five they report 82.41 on a loop that is unstable.

    part 2 · frequency
  3. The straight lines report 6.02 dB of gain margin on a loop that has none. computed by solving, not by drawing. The gain and phase of a loop made of an integrator and a pair at Q = 2, the corner at 1.00 kHz, the integrator set so that the straight-line asymptotes cross unity at 500 Hz. The loop's phase passes −180° at 1.00 kHz. There the lines put the loop gain at −6.02 dB and the solve at 0.00 dB, so the gain margin they report is 6.02 dB against 0.00 dB. The difference is 6.0206 dB, which is 20 log Q exactly with Q = 2, at any integrator gain. Closed, the loop is on the edge: the largest real part among its poles is -5.87e-17 of the corner's angular frequency.

    The gain margin the straight lines get exactly wrong

    A phase margin read off the straight lines is wrong by an amount that depends on where the loop crosses unity. A gain margin read off them is not: for an integrator and a pole pair the phase passes −180° at the pair's own frequency whatever the gain, and the lines are out there by exactly 20 log Q — 6.0206 dB for two real poles, 13.98 dB at a quality factor of five, at every integrator gain drawn. The stability condition for the loop turns out to be the same inequality: it is stable exactly when the gain margin the lines report exceeds that error.

    part 3 · frequency
  4. An order-8 Butterworth: the whole sketch is 3.0103 dB out at the corner, and its 4 sections −5.85 to +8.17 dB. computed by solving, not by drawing. The error of the straight-line sketch against the solved response — for each buffered section of an order-8 Butterworth lowpass at 1.00 kHz, and for the whole cascade. At the corner the sections are out by −5.852 dB (Q = 0.5098), −4.418 dB (Q = 0.6013), −0.915 dB (Q = 0.9000), +8.175 dB (Q = 2.5629), which add to −3.0103 dB: the whole filter's error, the same 10 log 2 as a single pole. The whole sketch is never further out than that anywhere; the section with the highest quality factor is +8.343 dB out at 1.04 kHz. The quality factors multiply to 1/√2.

    The corner error a filter hides in its sections

    The straight lines of an eighth-order Butterworth filter are 3.0103 dB out at the corner and nowhere worse — the same as one pole, at every order. The lines of the four sections it is built from are out by −5.85, −4.42, −0.92 and +8.17 dB there, which must add to the whole because the sections multiply. The whole sketch never gets worse with order and the worst section's error grows as 20 log(n/π). And the section the sketch misrepresents most is the one whose frequency error moves the filter most: 0.312 dB for one per cent, against the 0.173 dB any section's stopband shift gives.

    part 4 · frequency
  5. Lead zero at 500 Hz: the lines over-report by at most 3.12° with the loop's phase, and short by up to 20.6°. computed by solving, not by drawing. The error in the phase margin read off the straight lines of an integrator, two poles at 1.00 kHz and a lead section with its zero at 500 Hz and its pole 10 times higher, against where the lines cross unity, measured in decades from the zero. Gaps are placements where the lines are flat at unity or the loop crosses more than once. Read with the loop's own phase the reading is over by at most +3.12°, with the lines crossing −0.01 decades from the zero on a loop with 73.4° of margin, and never over on any loop with 60° or less; it is short by as much as 20.65°. Read with the phase off its straight lines too, on loops with 60° or less, it is never over.

    The zero that lifts the lines

    A phase margin read off the straight lines of an all-pole loop can only be short, and the proof takes three steps. A lead section breaks two of them: a zero's response lies above its lines, and between a zero and its pole the phase rises. The two breaks pull opposite ways, and measured across every placement of the crossing, in every sweep drawn, they leave an over-report of at most 6.58°, on a loop with 87.5°; on loops with sixty degrees or less it never exceeds 1.52°. The phase sketch is another matter: with the lines crossing at a lead zero above the plant's corner, it reports 17.91° on a loop with 1.17°.

    part 5 · frequency

All series