Circuit Response
every model has an edge, and the figure carries it
Concept

Form factor — where it appears

The ratio of a waveform's root-mean-square value to its mean, which is what a winding heats by and an average-responding meter has to assume. For a rectifier feeding a reservoir capacitor it is three or four rather than the 1.11 of a sinusoid, so the copper dissipates the square of that against a winding carrying the direct current alone.

Named by 4 essays across 2 fields — each of them below, with the objects they name alongside it.

Two meters, one current, and neither of them measuring the heat. computed by solving, not by drawing, at 35 conduction angles. The first curve is an average-responding meter: it rectifies, averages and multiplies by 1.1107, which is exactly right for a sinusoid — -7.8e-5% here — and exactly 11.07% high on a square wave, because the error is the ratio of two form factors and contains neither the amplitude nor the frequency. On a rectifier drawing its 100 W in sixty degrees of conduction it is -35.90% low. The second curve is a true-RMS meter that reaches 9 harmonics, which has no shape assumption in it and a bandwidth instead: it returns the root-sum-square of the lines it can see, and is one per cent low below every angle here of conduction. The crest factor at sixty degrees is 1.733, which is inside every instrument's rating — neither meter is failing because the peak is large. One is failing because the shape is not a sinusoid and the other because the spectrum is wider than it is.

What a meter multiplies by

An average-responding meter rectifies, averages and multiplies by 1.1107, which makes it exactly right for a sinusoid and wrong for everything else by the ratio of two form factors — 11.07 per cent high on a square wave and 35.9 per cent low on a rectifier drawing its current in sixty degrees. It is also exactly right at one other waveform, a 145.90 degree conduction angle, which is nobody's sinusoid. Beside it a true-RMS meter that reaches nine harmonics is two per cent low on a square wave and never within one per cent of anything narrower.

power · RMS and average The crest factor is 13.4 and the winding is sized by 3.01. computed by solving, not by drawing. Three ratios of the same settled march, against the reservoir. The crest factor — the peak diode current over the load's direct current — runs 6.43 to 24.25. The form factor, which is the root-mean-square current over the same direct current and is what a winding heats by, runs 2.114 to 4.077. Its square is the copper loss against a winding carrying the direct current alone, and that runs 4.47 to 16.62. The first ratio is 3.04 times the second at 220 µF and 5.95 times at 4700, so quoting one of them tells a reader nothing about the other.

The current that sizes the transformer

A reservoir's crest factor is 13.374 at a thousand microfarads and the winding is not sized by it. The root-mean-square of the same marched current is 3.0069 times the load's direct current, so the copper dissipates 9.0417 times what it would carrying the direct current alone — and the two ratios diverge, from 3.04 apart at 220 microfarads to 5.95 apart at 4700. The expression for the mean output is wrong in three places whose signs differ, and at 313.9 microfarads they cancel to six microvolts while the ripple expression inside it is still 32.3 per cent high.

applied · Unregulated supply A true-RMS reading of a sine: ripple a second filter removes, and a bias it cannot. An explicit converter — square, average through a one-pole of τ = 100 ms, take the root — in steady state on a sine of unit root-mean-square value, integrated exactly over a period at 91 frequencies and by a fourth-order march of its own equation at 6, which agree to 1.9e-8. The upper curve is half the ripple on the reading and the lower one the amount by which its mean is low. The reading is low at every frequency, because the square root is concave; it is 1% low below 1.86 Hz, while the ripple is inside ±1% only above 39.8 Hz. The dashed curve is the small-ripple form, an eighth of the averaged square's ripple power, which the bias approaches as the ripple shrinks.

The average a square root pulls low

A true-RMS converter squares, averages and takes the root, and the root of a quantity that ripples averages below the root of its mean. With a hundred-millisecond averager a sine is read one per cent low below 1.86 hertz, where the ripple is still ±20 per cent — and a second filter that steadies the display takes the ripple away and leaves the reading exactly as low as it was. A square wave is read exactly at any averaging time; a rectifier current conducting for twenty degrees needs 2.41 times the averaging a sine does. The implicit converter is the explicit one at half the time constant, and a reading falls 1.38 times slower than it rises.

power · RMS and average Summed over whole periods 1.3% too long, a sine is read to ±0.65% for up to 38 periods, whatever their number. Integrated exactly over each window, the worst over every starting phase. The error in a root-mean-square summed over N assumed periods 1.3% too long, against N, for a sine and a 60° rectifier current, beside an explicit converter averaging over a comparable time, τ of N/2 periods. For the sine the worst error is 0.643% at one period and stays near δ/2 until N approaches 1/(2δ) = 38; it vanishes where Nδ is a whole number of half-periods of the square, and beyond it is bounded by 1/(4πN). The rectifier current's is 1.274% at one period, near δ(CF² − 1)/2 with a crest factor of 1.732. The converter at τ = N/2 periods is low by 15.8 ppm on the sine at N = 10, with a ripple of ±0.796%; on the rectifier current, low by 46.3 ppm with ±1.665%.

The cycle a converter has to know

Summing a waveform's square over a whole number of periods reads its root-mean-square exactly: no averager, no ripple, no bias. It needs the period, and a period known one per cent long puts a hundredth of a period too much into the window. Wherever that extra piece falls, the reading moves — on a sine by up to 0.50 per cent over one period, and by 0.46 per cent over ten, because the extra piece grows with the window as fast as the window does. The worst error is δ(CF² − 1)/2, set by the crest factor and the period error and not by how many periods are summed, until the excess reaches half a period. A square wave is read exactly from any window, and a 60° rectifier current twice as badly as a sine.

power · RMS and average

Named alongside it

The objects these essays reach for when they reach for this one.

Conduction angleTrue-RMSCrest factorMeasurement conditionModel rangeAveragingDesign tradeoffReal powerRectificationReservoir capacitorSettling timeTotal harmonic distortion

All concepts