Circuit Response
every model has an edge, and the figure carries it
Concept

Mode conversion — where it appears

The appearance of one propagation mode from another, produced by any asymmetry between two conductors that were assumed identical. It is first order in the imbalance while the effect on the wanted mode is second order, so a pair can pass its own measurement and fail an emissions test.

Named by 7 essays across one field — each of them below, with the objects they name alongside it.

What 1.5 mm of length mismatch does to a differential pair. computed by solving, not by drawing. Two lines of the same impedance and different lengths, driven differentially. The solid rising curve is what arrives as common mode; the dashed one beside it is sin(ωΔτ/2), which is what a lossless pair gives and is the same curve until the null. The flat curve at the top is the differential signal, and it is the point: at 3.04 GHz a tenth of the launched amplitude is common mode and the differential has lost 5011 parts per million of itself. The conversion is first order in the skew and the loss is second order, so the error is not missing from the signal — which is why a pair can pass its own eye and fail an emissions test. At 95.3 GHz the closed form has a null and the real pair does not: the longer conductor is also the lossier one, and an amplitude imbalance has no null in it.

The millimetre that becomes common mode

A pair carries two modes rather than two signals, and a length mismatch between its halves converts one into the other. A millimetre and a half of skew is ten picoseconds, a tenth of the signal is common mode by three gigahertz, and the differential signal has lost five thousand parts per million of itself getting there — so the error is not missing from the signal, which is why a pair can pass its own eye and fail an emissions test. The product in the answer is ωΔτ, which is what the instruments field's rejection corner is one over.

lines · Differential line One part, two corners: 3.98 kHz to the common mode and 7.86 MHz to the signal. computed by solving, not by drawing. Two windings on one core with a coupling of 0.999, driven twice from the same netlist — once with the two conductors in opposition, which is the signal, and once with them in parallel, which is everything the cable picked up. The mode that goes the same way round both windings meets (1+k)L and is down three decibels by 3.98 kHz; the mode that goes opposite ways meets the leakage, (1−k)L, and is untouched until 7.86 MHz. The ratio is 1975, which is 2/(1−k) and contains no inductance at all. Neither number is computed here: both modes are driven and the answer is read.

The inductor one mode cannot see

Two windings on one core present a millihenry to a current that goes the same way round both and a microhenry to one that goes opposite ways, so the same component has a corner at 3.98 kHz and another at 7.86 MHz — a ratio of two thousand, which is 2/(1−k) and contains no inductance at all. It is bought to remove the conversion the previous essay measured, and five picofarads across each winding turn it over at 1.59 MHz and leave it worth 0.02 decibels by ten gigahertz.

lines · Common-mode choke The null is a V and not a bowl: one per cent of ratio error is 5.0e-3 of the near end. computed by solving, not by drawing. The same twelve coupled sections read at 10.0 MHz, with the ratio of the two couplings swept across the null rather than sat at one setting. The far end divided by the near end is |1 − r|/(1 + r) at every point — a straight-sided V through zero, first order in the departure with a coefficient of one half, and not a rounded minimum with a flat bottom. So there is no tolerance band: a ratio one per cent off gives 4.98e-3 of the near end and ten per cent off gives 4.76e-2, and the exchange rate between them is fixed. The upper trace is the near end over the same sweep, which moves by 11 per cent while the lower one moves through 14 decades — the two ends are the same coupling read as a sum and as a difference, which is why one of them has a zero in it and the other cannot.

How wide a null is

A far end at 3.5×10⁻¹⁹ of the drive is a statement about arithmetic until somebody asks how far the two couplings may differ before it comes back. The answer has no flat bottom in it: the far end divided by the near end is |1−r|/(1+r) exactly, so the null is a V and a ratio one per cent off returns 4.98×10⁻³ of the near end. On the axis a board is built to that is a difference of 0.0081 between the two modes' effective permittivities, out of 3.99 — two parts in a thousand, and 0.675 picoseconds of mode skew over a hundred millimetres.

lines · Crosstalk Three imbalances, three slopes: a 2% amplitude imbalance is 1% common mode at every frequency, 1 mm of skew overtakes it above 455 MHz, and a 5 ps rise-time mismatch climbs at forty decibels a decade. computed by solving, not by drawing, from the transforms of the two conductors' edges and checked against the sampled edges transformed by FFT to two per cent: the common mode at the far end of a pair, as a fraction of the differential, for three separate imbalances between its halves. An amplitude imbalance of 2% gives 1.00% at every frequency. A skew of 1 mm on FR-4, 7.00 ps, gives sin(ωΔτ/2), rising at twenty decibels a decade: 2.20% at 1 GHz. Edges of 50 and 55 ps, perfectly timed and equal in size, give a common mode rising at forty decibels a decade: 0.043% at 1 GHz and 5.38% at 10 GHz. The skew passes the amplitude imbalance near 455 MHz, which is a/(2πΔτ).

The common mode that has three slopes

A differential pair turns into common mode wherever its two halves differ, and they can differ in three ways — in size, in timing and in edge rate — each with its own slope. A 2 per cent amplitude imbalance is 1 per cent common mode at every frequency. A millimetre of skew rises at twenty decibels a decade and overtakes it above 455 MHz, a/(2πΔτ). Edges of 50 and 55 picoseconds, perfectly timed, rise at forty: 0.043 per cent at a gigahertz and 5.4 at ten. In time they are a step that stays, a pulse with an area, and a doublet with none — each slope is a moment that vanishes. And an amplitude imbalance and an edge-rate mismatch of the right signs cancel at one frequency, down 74 dB, which half a picosecond of skew fills back to −25.

lines · Differential line Routed along the glass weave, a length-matched pair with one conductor over a bundle and one over a gap builds 63.6 ps of skew in 20 cm — the skew nobody routed. computed by solving, not by drawing by integrating each conductor's delay along its route: a length-matched pair of 0.25 mm pitch over a glass weave of 0.5 mm pitch whose effective permittivity swings between 4.2 and 4.6 across it, positioned so that one conductor runs over a bundle and the other over the gap. Routed along the weave (dashed) the skew grows in proportion to the length, 0.318 ps a millimetre, to 63.62 ps in 200 mm. The slider rotates the route.

The skew in the glass

Match a differential pair's two lengths exactly and it can still have tens of picoseconds of skew, because a circuit board is woven glass in resin and the two conductors need not sit over the same one. Over a weave of half a millimetre whose effective permittivity swings from 4.2 to 4.6, a pair of quarter-millimetre pitch with one conductor over a bundle and the other over a gap builds 0.318 ps of skew every millimetre — 63.6 ps in 20 cm, the equivalent of 13.6 mm of routed mismatch by 30 cm, and 68 per cent common mode at 2.5 GHz. Where the pair falls across the weave is a lottery from nothing to that. Rotate the route by ten degrees and the skew never exceeds 0.146 ps, however long the pair: each conductor crosses bundle and gap in turn, and the difference averages out.

lines · Differential line With the weft counted as well as the warp, the skew a pair can reach is least at 45.0° to the warp — 128 fs — and turning further off the warp makes it worse again. computed by solving, not by drawing, to first order in the permittivity's swing, the summed bound held against an integration over 64 registrations of the pair to the cloth at six angles. A 0.25 mm pair over a cloth whose warp has a 0.5 mm pitch and whose weft has a 0.5 mm pitch, each swinging the permittivity by ±0.2 about 4.4. The warp's contribution falls as the route turns off it, as the earlier figures found; the weft's rises, because the pair's projection across the weft grows as d·sin θ while its yarns are crossed less often. The worst skew is least at 45.00°, 128.3 fs. At 10°, where the warp alone allows 291.4 fs over every registration — twice the earlier figure's 146 fs, which was for a route starting over bundle and gap — the weft adds 13.8 fs. Integrated: 5° 587.6 fs, 15° 215.1 fs, 30° 139.3 fs, 40° 126.3 fs, 60° 139.2 fs, 80° 304.9 fs. The slider is the weft's pitch.

The angle two weaves allow

Turning a differential pair a few degrees off a board's glass weave stops its skew growing with length — but a cloth has two weaves, and turning off the warp turns onto the weft. Counting both, the worst skew over every registration of the artwork to the cloth is a sum of two bounds, one falling as the route leaves the warp and one rising as it meets the weft, and it is least at an angle the cloth decides: 45° and 128 fs for two identical half-millimetre weaves and a quarter-millimetre pair, against 305 at 10°; 52° for a finer weft; 67° for a flatter one. Doing the count properly also finds the earlier bound a factor of two low, and finds the obvious answer a trap: on a square weave's exact diagonal the two weaves' product stops averaging and the skew grows again, 2.2 fs a millimetre, while a degree either side it stays at 128.

lines · Differential line A pair with one conductor over glass-rich laminate (4.6, tan δ 0.015) and one over resin-rich (4.2, tan δ 0.025): the skew per millimetre against frequency. computed by solving, not by drawing: each conductor as its own causal line — permittivity dispersing with its own loss tangent, copper with its internal reactance — and the skew as the difference of their delays. With both permittivities held at their 1 GHz values the skew would be 0.318 ps/mm at every frequency (level line). Dispersing, it is 0.272 ps/mm at 100 MHz, 0.319 at 1 GHz and 0.366 at 10 GHz: the resin, lossier, loses permittivity faster with frequency, and the gap between the two halves widens.

The skew that moves with frequency

A pair with one half over glass-rich laminate and one over resin-rich builds 0.318 ps of skew a millimetre when each permittivity is held at its 1 GHz value. But the two regions lose differently — tan δ 0.015 against 0.025 — so their permittivities fall at different rates, and the skew is a curve: 0.272 ps/mm at 100 MHz, 0.319 at 1 GHz, 0.366 at 10 GHz. A deskew set at one frequency leaves ±2.35 ps in 50 mm at the other two. The resin half also loses 3.7 dB more by 10 GHz over 200 mm, so its edge arrives 63.7 ps early and rises in 257 ps against 202; the halves differ in timing and in edge rate at once, and leave a common-mode pulse of 151 mV for each volt.

lines · Dispersion

Named alongside it

The objects these essays reach for when they reach for this one.

Differential lineSkewHomogeneous dielectricPermittivityPropagation velocityCommon-mode rejectionCrosstalkDesign tradeoffEmissionsMutual inductanceRise timeCharacteristic impedance

All concepts