A 1 V step onto 1.00 m of 50 Ω line into an open circuit
Drawn above at its default parameters, which is almost never how an essay calls it. A placement states the numbers that essay is arguing about, so the figure a reader meets is about that argument rather than about the generator — 98% of the placements on this site pass one, and the phase that raised that number from 12% found eight captions describing a figure the page was not showing.
At those defaults the edge it states is nothing at the far end before 4.83 ns — the right-hand slot
of the caption strip, which on this site is never used for anything else, and which is read
back out of the drawing above rather than out of the code that wrote it.
It belongs to Lines, where a wire has a length, which is to say a change to it is a
change to lib/figures/lines.js.
It takes a slider on load resistance (ohms) with 7 settings,
and every one of them has passed the same assertions as the frame above — a figure whose
circuit stops doing what its caption says at any setting stops the build.
Called by 5 essays
which is the blast radius of changing it
The staircase in time
A source driving a metre of cable does not know what is on the far end of it for 4.83 nanoseconds. What it drives into during that time is decided by the cable's characteristic impedance and nothing else — and when the far end finally answers, the answer comes back as a staircase whose limit is the resistive divider the circuit was going to be all along.
The resistor at the wrong end
A lattice diagram is read at the two ends of a line, and that is where the two respectable terminations look identical: a clean step, one delay late, at the receiver. Anyone standing halfway along a series-terminated net sees half the swing held for a full round trip, which for a logic input is not a level at all. The interval is 2(1−x) delays exactly, it is zero only at the far end, and the scheme that never has it draws sixty milliamperes for as long as the level is held.
The dip whose area is fixed
A picofarad across a 50 Ω line makes a dip in what comes back. Its depth is 0.833 volts to a six-picosecond edge and 0.0196 volts to a nanosecond one, forty-two times less; its area is 25 picoseconds to both, to six parts in a hundred thousand, because the area is Z₀C/2 and contains nothing about the edge. Two half-picofarad discontinuities too close to tell apart read as exactly one picofarad, and so do two far enough apart to be separate — the area is additive where the depth is not. And what a reflectometer calls the capacitance of an impedance step is the step's real excess capacitance times 1 + Z/Z₀.
The via two lines can weigh
The area under a reflection is a property of the discontinuity rather than of the edge, and for a via it is one number made of two: −Z₀C/2 from its pads and +L/2Z₀ from its barrel, with opposite signs. A via of half a picofarad and a nanohenry, seen from fifty ohms, leaves 2.5 picoseconds of dip — which a reading that assumes a capacitor calls 0.100 pF, a fifth of what is there. From fifty and seventy-five ohms together the two areas give 0.5000 pF and 1.0000 nH back, and fifty femtoseconds of error on each costs 0.8 per cent of the capacitance and 1.5 of the inductance. A second line at fifty-five ohms costs five times as much.
The via that is a piece of line
A via of half a picofarad of pad and a nanohenry of barrel puts no area under its reflection from a line of √(L/C) = 44.72 ohms, from any edge. It has not vanished. It delays the edge going past it by 22.4 picoseconds, which is √(LC) exactly, and it still reflects: a doublet whose largest excursion falls as the −1.99 power of the edge where a lone capacitance's falls as the −0.97 — 24.4 millivolts for a 59-picosecond edge against 166 for the pads alone, and 994 microvolts for a 295-picosecond one against 35. The balanced via is a short piece of line, and the reflection it leaves is the reflection of its length rather than of its size.