Concept

Compliance range — where it appears

The range of output voltage over which a current source holds its current to a stated band, which has a top as well as a bottom. Its floor is where a transistor saturates and its ceiling is where the Early effect has carried the current out of the band, so a cascoded source with a higher floor can have five times the usable range.

Named by 3 essays across one field — each of them below, with the objects they name alongside it.

A copy out by 1.3% for the reason everybody names, and 11% for the one nobody does. computed by solving, not by drawing at 60 output voltages, with the Early conductance iterated to self-consistency against the current that sets it. Two base currents are stolen from the reference, so the copy is β/(β+2) of it — 1.32% low at β = 150 — and that is exact at exactly one output voltage, 0.7043 V, which is 9.39 mV under the reference's own base-emitter voltage of 0.7137 V — a displacement that goes as 1/(β+2), so that the product of the two is 1.427 V at every β the slider offers. Everywhere else the Early effect is larger: the current rises at 1.21% per volt, so moving the output from one volt to ten changes it by 11.2%. One per cent holds over 0.810 V, which is the Early voltage over a hundred and contains neither the current nor any resistor. The slider is β: it moves the first error by fifty times and the second by nothing at all.

The copy, and its two errors

Every account of a current mirror leads with the base currents: two are stolen from the reference, so the copy is beta over beta plus two, which is 1.32 per cent at beta of 150 and is what a third transistor is spent on. The Early effect is a footnote and is nine times larger over any useful swing — 11.2 per cent between one volt and ten. Moving beta from 20 to 1000 changes the first by a factor of forty-five and the second by nothing at all.

semiconductors · Current mirror

A cascoded mirror is 90× the output resistance, and 43% of it goes back into the reference. computed by solving, not by drawing. The output resistance of a two-transistor mirror and of the same mirror with a cascode on each branch, measured by moving the output a little either side of its operating point and reading the current, against the current gain of every device. The plain mirror sits at rₒ = 89 kΩ and does not move. The cascoded one reaches 7.39 MΩ at β = 150 and rises with β until β stops being the smaller of the two quantities, where it saturates on gₘrₒ² = 268 MΩ. The third curve replaces the diode-connected upper device with a held voltage at the same potential and recovers 1.76 times the resistance, which is the upper device's base current being charged a second time — to the reference branch, where it moves the mirror's own bias.

The source that holds to the supply

Putting a second transistor on each branch of a current mirror is always described as buying output resistance and costing headroom, and both halves of that are measured here rather than repeated. The resistance goes from 82 kΩ to 7.39 MΩ, the floor rises by 0.71 volts — and the range over which the current is actually what it was set to goes from 1.70 volts to 9.09, because a plain mirror's current never stops climbing. Forty-three per cent of the resistance that should be there is missing, and it is in the reference branch.

semiconductors · Cascode

One output in saturation takes 6.5% off another that is at five volts. computed by solving, not by drawing. A three-transistor mirror: a reference, an output taken down into saturation, and a third output held at five volts throughout. The upper curve is the saturating output's own loss and the lower one is the sibling's. At 50 mV the saturating output is 27.3 per cent down and the sibling, which is nowhere near saturation, is 6.54 per cent down. The reference current moves by -0.0188 per cent, which is nothing: a base current is a hundred and fiftieth of a collector current and the reference is set by a resistor from the supply. What does move is the base-emitter voltage every output shares — by -1.75 millivolts — and every output is an exponential of it.

The refusal, and what it was protecting

A current mirror's model has declined to answer below two hundred millivolts of collector-emitter voltage since it was written, because it has no base-collector junction and would return a forward-active current for a saturated transistor. Put the junction in and the refusal turns out to have been placed where the model it protects is still right to seven parts in ten thousand — and the mirror's real failure is somewhere else entirely: a saturated output takes six and a half per cent off an output that is sitting at five volts.

semiconductors · Current mirror

Named alongside it

The objects these essays reach for when they reach for this one.

Current mirror Operating point Early effect Model range Newton raphson Output impedance Cascode Design tradeoff Device matching Model refusal Saturation Thermal voltage

All concepts