Concept

Small-signal model — where it appears

A device replaced by the linearisation of its own curve about an operating point, valid up to an amplitude computed from that curve. The amplitude it is valid up to is measured rather than assumed, and for an exponential device it is a few millivolts.

Named by 12 essays across 2 fields — each of them below, with the objects they name alongside it.

Linearising an exponential at 27 °C, and what it costs. The linear model understates the gain by 1% at 7.30 mV and by 10% at 22.8 mV. The thermal voltage at this temperature is 25.9 mV, so "small compared with Vₜ" is not the criterion — 28% of Vₜ is already 1% wrong.

How small is small signal

Linearising an exponential replaces a curve by its tangent, which is exact at a point and progressively wrong away from it. The amplitude at which it is one per cent wrong is 7.3 millivolts at room temperature — 28 per cent of the thermal voltage, not a small fraction of it, and a good deal smaller than "small signal" suggests.

limits · Small-signal

A follower's output impedance from 1 kΩ of source, bare and with 100 pF on it. computed by solving, not by drawing, on a small-signal follower at 2.0 mA with β = 150 and fT = 560 MHz. At 100 Hz the emitter presents 19.08 Ω against a textbook 1/gₘ + Rₛ/(β+1) of 19.55 Ω — the expression is an upper bound here and at every source resistance on the slider, 2.4% high at this one. What it cannot describe is the frequency axis: the β that divided the source resistance down is itself falling, so the impedance rises, and the reactance at 3 MHz is 4.3 Ω — an inductance of 0.229 µH against Rₛ/ωT = 0.284 µH. With 100 pF hung on the output that impedance peaks at 67.0 Ω at 29.3 MHz, 3.51 times its own low-frequency value: an inductive source and a capacitive load are a resonant circuit, and this one is inside a part whose output impedance is quoted as a single number.

The buffer that is not a buffer

An emitter follower is reached for when something has to be driven without being loaded: unity gain in, high impedance seen, low impedance presented. The last of those is a number with a range, and the range is narrow. At a kilohm of source the emitter presents 19.08 ohms at low frequency and 67 ohms at 29 megahertz, because the current gain that made it small is falling — and the peak is worst in the middle of the slider, so it cannot be avoided by making the source stiffer or softer.

semiconductors · Emitter follower

Linearising an exponential at 125 °C, and what it costs. The linear model understates the gain by 1% at 9.69 mV and by 10% at 30.2 mV. The thermal voltage at this temperature is 34.3 mV, so "small compared with Vₜ" is not the criterion — 28% of Vₜ is already 1% wrong.

The edges that move with the room

Every boundary in this collection is quoted at one temperature and most of them are functions of it. The small-signal edge is proportional to the thermal voltage, so it runs from 5.67 millivolts at −40 degrees to 9.69 at +125 — a factor of 1.71, the ratio of the absolute temperatures exactly. A realised Q is 1.54 per cent high at one end of that range and 2.58 at the other. The numbers are right; the condition attached to them was left off, and it is the same condition every time.

limits · Model edges $Two of the three are one mechanism at 19.0°; the third arrives at ninety. computed by solving, not by drawing. The cosine between each pair of error waveforms at 30.0 kHz, against how much output the ideal model is asked for. Bandwidth and slewing sit at 0.9454 — 19.0 degrees — and close only slowly, reaching 0.8813 at 16 V. Clipping does not exist below 12.00 V, where its error is 4.0e-9 per cent of the signal and its direction is the direction of rounding; above it the mechanism is real — 18.1 per cent at the top of the sweep — and its cosine against both of the others stays under 0.0025. The bandwidth error is 0.615 per cent at every amplitude here, unchanged to 5.3e-15, because a linear stage's fractional error has no amplitude in it.$

Where the mechanisms are one mechanism

An amplifier is said to run out of three separate things — bandwidth, slew rate and rails — and errors from separate mechanisms add in quadrature while errors from one mechanism add as magnitudes. Measured as waveforms rather than as numbers, two of the three sit 18.4349 degrees apart, which is exactly the angle between a sinusoid and its own cube, and the third sits at ninety: its cosine against both of the others stays under 0.0025 wherever it exists. So the arithmetic is neither of the two anybody reaches for, and a budget built the right way is within 2.9 per cent where quadrature is 17 per cent low and a straight sum 37 per cent high.

limits · Small-signal

Three amplitudes, all of them one per cent

The amplitude at which linearising an exponential is one per cent wrong is 7.30 mV, and that is a statement about the gain. Two other quantities are also one per cent wrong somewhere: the second harmonic reaches one per cent at 1.03 mV and the shift in the operating point the model was linearised about reaches it at 5.17 — which is √2 below the gain boundary exactly, because the mean goes as a²/4 and the fundamental as a²/8. And the spacing is not a property of the device: tighten the criterion to a part in ten thousand and the same three spread to 1 : 50 : 70.7.

limits · Small-signal

What a pair does to the three boundaries: removes two, moves one. computed by solving, not by drawing, with every harmonic taken from a transform of the waveform rather than from a series. A differential pair's transfer is an odd function, so the mean and every even harmonic are zero — -3.2e-17 and 9.1e-17 at a drive of two thermal voltages, which is absent rather than small. Two of the three one-per-cent boundaries therefore do not exist for a pair at all. The third, the loss of gain, moves by √2 in the limit of a tight criterion and by 1.42610 at the one per cent quoted here — 10.42 mV against 7.304 mV at 27 °C, against √2 = 1.41421 and 1.41433 at a criterion a hundred times tighter. So a pair reached for as headroom has bought forty per cent of it and a pair reached for as linearity has bought something else entirely. Twenty millivolts of imbalance brings the even orders straight back, which is what says the cancellation belongs to the symmetry rather than to the topology.

Two boundaries removed, and one moved

A differential pair's transfer is odd, so its mean and every even harmonic are zero — −3.2×10⁻¹⁷ and 9.1×10⁻¹⁷ at a drive of two thermal voltages, absent rather than small. Two of the three one-per-cent boundaries therefore do not exist for a pair at all. The third, the loss of gain, moves by √2 in the limit and by 1.42610 at the one per cent usually quoted: 10.42 mV against 7.304. So a pair reached for as headroom has bought forty per cent of it, and twenty millivolts of imbalance brings the even orders straight back.

limits · Small-signal $At gₘRₑ = 1 a pair holds its gain to one per cent up to 29.2 mV, a single transistor to 29.9 mV. computed by solving, not by drawing, every point a waveform solved sample by sample and its fundamental read from its transform. The fractional departure of the fundamental from the small-signal gain against the peak drive, for a differential pair (solid) and a single transistor (dashed), each device with an emitter resistor of 1 times its own 1/gₘ at 27 °C. The pair reaches one per cent at 29.2 mV; the cubic law 0.4·Vₜ·(1 + gₘRₑ)^(3/2) says 29.3 mV, which holds while the drive leaves most of the tail unsteered and overstates the boundary beyond; the single transistor at 29.9 mV, a ratio of 0.974. Without degeneration the ratio was √2 in the limit; with heavy degeneration it approaches two; and near gₘRₑ = ½, where the single transistor's cubic vanishes, the single transistor briefly holds its gain longer.$

Symmetry and a resistor together

A pair linearises by symmetry and an emitter resistor by feedback, and the two are normally used together. Solved together, the pair's one-per-cent gain boundary is 0.4·Vₜ times (1 + gₘRₑ) to the three-halves power up to gₘRₑ = 3: 10.4 mV bare, 29.2 mV at gₘRₑ = 1, 80.9 at 3. The √2 by which it outlasted a single transistor does not survive: at gₘRₑ = 1 the two are within three per cent, near ½ the single transistor outlasts the pair fourfold, because its cubic vanishes there and a pair's never can, and with heavy degeneration the ratio climbs to 1.95 at gₘRₑ = 50 — two, for a reason that has nothing to do with junctions: a single transistor cuts off when the drive reaches Ic·Re, and a pair has steered its whole tail at 2·Ic·Re, its two emitter resistors in series. What symmetry alone buys is the even orders, at every degeneration.

limits · Small-signal

With 1 mV of offset the pair's second harmonic returns in proportion to the drive, and the third harmonic reaches one per cent first. computed by solving, not by drawing, every harmonic read from a solved waveform. A differential pair at 27 °C with 1 mV of input offset: its second harmonic (solid) and third (dashed) over its fundamental, against the peak drive, beside a single transistor's second harmonic (dotted). The third is the balanced pair's own, u²/12, and reaches one per cent at 17.9 mV whatever the offset. The second is (u/2)·tanh(Vos/2Vₜ) at small drive, the single transistor's second harmonic times tanh(Vos/2Vₜ) = 1.93e-2, and never reaches one per cent: it peaks at 0.74% as the pair begins to saturate and falls again.

The offset that brings the even orders back

A balanced pair has no second harmonic. An offset gives it one, and the closed form is exact: the second harmonic over the fundamental is (u/2)·tanh(Vos/2Vₜ), with u the drive over 2Vₜ — a single transistor's second harmonic times the fraction of the tail the offset steers aside, 1.93% of it at a millivolt, not the twentieth usually estimated. It is first order in the offset up to 9.0 mV. It does not grow with the drive for ever: it peaks as the pair saturates and falls again, so below 1.36 mV of offset it never reaches one per cent at any drive, and above 3.14 mV it reaches one per cent before the pair's own third harmonic does, at 17.9 mV. Read the other way, a matching specification is a distortion specification: −60 dB of second harmonic at 10 mV of drive allows 0.535 mV of offset.

limits · Small-signal $Degenerated to gₘRₑ = 1, a pair with 1 mV of offset peaks at 0.41% of second harmonic, against 0.74% bare. computed by solving, not by drawing, every harmonic read from a solved waveform. The second (solid) and third (dotted) harmonics, as fractions of the fundamental, of a differential pair with 1 mV of input offset and emitter degeneration gₘRₑ = 1, against the peak drive; the same pair undegenerated in grey (dashed: second; dot-dash: third). Degeneration lowers both and moves both to larger drives. At small drive the second harmonic follows (u/4)·g″/g′² at the offset's operating point, which for a small offset is (u/2)·(Vos/2Vₜ)/(1 + gₘRₑ)³. Its largest value over all drives is 0.406 per cent at 177 mV, against 0.736 per cent at 76 mV undegenerated.$

Two decibels of matching for one of gain

An offset gives a differential pair back the second harmonic its symmetry removed. Put resistors in the emitters and that second harmonic falls as the cube of one plus gₘRₑ at a fixed input and as its square at a fixed output — measured slopes of −3.00 and −2.00 — so each decibel of gain given up buys two decibels of distortion, or two decibels more offset at the same distortion. A matching specification that allowed 0.535 mV for −60 dB at 10 mV of output allows 2.14 mV at gₘRₑ = 1. The worst case over all drives relaxes more slowly: the offset below which the second harmonic can never reach one per cent goes from 1.36 mV to 4.39 mV as gₘRₑ goes to three, because the peak it limits sits where the pair saturates, and degeneration only moves that further out.

limits · Small-signal

Where a chain of 4 stages stops obeying its model, against where one stage does. computed by solving, not by drawing. amplifier, 1%: one stage 14.2 kHz, 4 stages 7.06 kHz, a ratio of 0.498; Kirchhoff, 1°: one stage 3.97 MHz, 4 stages 993 kHz, a ratio of 0.250; small-signal, 1%: one stage 7.30 mV, 4 stages 7.26 µV, a ratio of 0.000995. The amplifier's edge moves as N to the −½ because its error grows as the square of frequency; the board's as N to the −1 because a phase grows in proportion; and the small-signal edge collapses, because the last stage sees the gain of all the others.

The edge of a chain

A system built from stages that are each inside their own edge is not inside its own: the stages share one error budget. Four ×10 stages from a 1 MHz amplifier are 1% from ideal at 7.06 kHz, not at the single stage's 14.2 kHz — the edge moves as N to the −0.502. A signal path through four ten-centimetre boards is a degree long at 993 kHz, a quarter of one board's edge, as N to the −1. The chain's exponent is minus the edge's own exponent in its tolerance, measured on the line y = −x. And the small-signal edge of a chain with gain belongs to its last stage: four junction stages of ten are 1% off at 7.26 µV, a thousandth of one stage's 7.30 mV.

limits · Model edges

At a fixed output a 0.5 mV junction mismatch's second harmonic falls as (1 + gₘRₑ)⁻² and a 1% resistor mismatch's as (1 + gₘRₑ)⁻¹: past gₘRₑ = 1.93 the resistors set it. computed by solving, not by drawing, every waveform solved arm by arm in currents. A pair on a 1 mA tail, its output held at what the bare, balanced pair gives for 10 mV of peak drive; the second harmonic over the fundamental from a 0.5 mV VBE mismatch alone (dashed), from a 1% mismatch between the emitter resistors alone (dotted), and from both in the same sense (solid), against one plus the degeneration. Between gₘRₑ = 5 and 20 the junction's falls with slope −2.00 and the resistors' with −0.89, still approaching −1, since the local slope of gₘRₑ/(1 + gₘRₑ)² is 1/gₘRₑ − 1. The resistors' mismatch is an input offset of Vₜ·gₘRₑ·δ, which grows with the degeneration that divides it, so the two cross where gₘRₑ = ΔVBE/(Vₜδ) = 1.93; beyond it each decibel of gain given up buys one decibel of distortion, not two.

The resistor mismatch that is only an offset

Two emitter resistors that differ by δ unbalance a degenerated pair, and with an ideal tail they do it in the simplest way possible: the arm currents always sum to the tail, so the mismatch adds the constant (Iₜ/2)·R·δ = Vₜ·gₘRₑ·δ to the input and nothing else. Solved arm by arm, a 1% mismatch at gₘRₑ = 3 is the balanced pair moved by 0.776 mV to 4 × 10⁻¹⁶ of the tail, and a trim of that size leaves no second harmonic at any drive. What separates it from a junction's offset is that it grows with the degeneration meant to divide it: at a fixed output its second harmonic falls as gₘRₑ/(1 + gₘRₑ)², one decibel per decibel of gain rather than two, and it takes over from 0.5 mV of base–emitter mismatch at gₘRₑ = 1.93. For −80 dB at 10 mV of output the resistors must match to 0.823% at gₘRₑ = 1 even with perfect transistors.

limits · Small-signal

A 1 MHz sine of 1 V into an emitter follower with 1 nF on its emitter and a 2 mA sink: the input falls at up to 6.28 V/µs, the output can fall at only 2.0, and the transistor switches off. Marched, the base driven by a stiff source and the emitter current Is·exp((vᵢₙ − vₒᵤₜ)/Vₜ). The input (dashed) and the output (solid) over the last of four cycles. The input's steepest fall is 2πfA = 6.28 V/µs; the load can be discharged no faster than the sink allows, I/C = 2.00 V/µs. On every falling stretch the base–emitter junction reverse-biases, the emitter current drops below a hundredth of the sink's (dots), and the output falls as a straight line of slope −2.000 V/µs until the input comes back up to meet it. On the rising half the transistor pushes whatever current the capacitor needs and the output follows a Vbe below the input.

The follower that lets go on the way down

An emitter follower can push current into its load without limit and pull it out only through whatever sinks the emitter. Marched as a large-signal circuit — a 2 mA sink, 1 nF on the emitter — a 1 V, 1 MHz sine asks the output to fall at up to 6.28 V/µs, the sink allows 2.00, and on every falling stretch the junction reverse-biases, the emitter current drops below a hundredth of its quiescent value for 57% of the cycle, and the output falls as a straight line of exactly −I/C. The boundary is a slope, 2πfA ≤ I/C: 2.87 V at 100 kHz, 0.309 V at 1 MHz, creeping above the line only as the period approaches the junction's own 12.9 ns. Past it the follower rectifies — its output's average rises 415 mV at 1 V of drive and 1.30 V at 2 V — and with a resistor in place of the sink the fall slows as the output descends, from 2.41 V/µs to 1.99. None of it is visible to the small-signal model the earlier essays used.

semiconductors · Emitter follower

Named alongside it

The objects these essays reach for when they reach for this one.

Thermal voltage Validity region Differential pair Even-order distortion Model range Emitter degeneration Gain–bandwidth product Capacitive load Design tradeoff Device mismatch Emitter follower Even harmonic cancellation

All concepts