Circuit Response
every model has an edge, and the figure carries it
Concept

Thermal voltage — where it appears

kT over q, some twenty-six millivolts at room temperature, which is the scale on which a junction's exponential law bends. It appears in every amplitude boundary a junction has, so those boundaries are proportional to absolute temperature and are quoted at a stated one.

Named by 21 essays across 6 fields — each of them below, with the objects they name alongside it.

Linearising an exponential at 27 °C, and what it costs. The linear model understates the gain by 1% at 7.30 mV and by 10% at 22.8 mV. The thermal voltage at this temperature is 25.9 mV, so "small compared with Vₜ" is not the criterion — 28% of Vₜ is already 1% wrong.

How small is small signal

Linearising an exponential replaces a curve by its tangent, which is exact at a point and progressively wrong away from it. The amplitude at which it is one per cent wrong is 7.3 millivolts at room temperature — 28 per cent of the thermal voltage, not a small fraction of it, and a good deal smaller than "small signal" suggests.

limits · Small-signal What a 0.7 V constant costs, in the quantity it is used to predict. computed by solving, not by drawing by Newton's method on the exponential at 94 supplies through four resistors. The model is exact at 5.748 mA — the current at which the true drop is 0.7 V — and every curve crosses zero there, at four different supplies. Below it the model is low and above it high, and how much depends on the headroom rather than on the diode. Through the 87 Ω curve the drop is 49 mV out at 0.725 V and 147 mV out at 150.7 V — a factor of 3.0 — while the error in the current falls from -66% to 0.10%, a factor of 674, because the headroom underneath it has grown by 2017. On that curve the model is inside one per cent only above 1.12 V.

The one current a constant is right at

Seven-tenths of a volt is the true forward drop at 5.748 milliamperes and at no other current, and every circuit built on it crosses zero error there — four different resistors at four different supplies, all exact at the same current. What decides whether the model is any good is not the diode at all; it is how much of the supply the diode is taking.

limits · Diode model A diode's drop from 250 to 400 K, at 1.00 mA. computed by solving, not by drawing. Thirty-one operating points, each Newton's method on the exponential at its own temperature. The drop falls at 1.828 mV/K measured against 1.830 mV/K from the closed form — falls, although the thermal voltage in the exponent rises, because the saturation current rises faster. Over the same range the slope per decade of current goes the other way, from 49.6 mV to 79.4 mV, because that one is Vₜ ln 10 and nothing else.

Two millivolts a kelvin, and the wrong sign

Every number in the semiconductor field was computed at 300 K, and the model had no temperature in it at all. Putting it in moves a diode's drop by 1.828 mV/K — downwards, although the thermal voltage in the exponent is rising, because the saturation current rises by nine orders of magnitude across the same range. Two temperature dependences of one device, of opposite sign, from one solve.

semiconductors · Temperature Two floors on one axis, and the 50.0 mV between them. computed by solving, not by drawing. The flat line is the Johnson current noise of 1 kΩ, √(4kT/R), which has no current in it. The rising line is shot noise, √(2qI), which has no resistance in it. They cross at 50 µA — and the direct voltage across the resistance there is 49.981 mV, which is 2kT/q and contains neither quantity. The slider moves the resistance over six decades; the crossing moves with it and the voltage at the crossing does not move at all, to the last bit of a double.

The floor a current sets

A resistor's noise contains no current and a current's noise contains no resistance, and the two are equal when the direct voltage across the thing carrying the current is 2kT/q — 50.0 millivolts at 290 kelvin, whatever the resistance and whatever the current. It is the only boundary in this collection whose axis is a direct voltage across an element. And a forward-biased junction, which has the same dynamic resistance as some resistor, produces exactly half its noise power at every current.

noise · Shot noise What a 5% mismatched pair leaves behind, across 150 K. computed by solving, not by drawing. A saturation-current mismatch of 5.0% appears as an input offset of Vₜ·ln(m) — 1.2613 mV at 300 K — which is proportional to absolute temperature and therefore drifts at 4.2044 µV/K, exactly the offset divided by the temperature. That is 3333 ppm per kelvin at every mismatch on the slider, because the ratio is 1/T and contains nothing about the device. One junction on its own drifts 1.828 mV/K, 435 times harder.

What matching does about temperature

A pair cancels the 1.8 mV/K that broke the previous essay, and what it leaves behind is exact: a saturation-current mismatch of m shows up as an offset of the thermal voltage times ln(m), which is proportional to absolute temperature and therefore drifts in proportion to itself. 3 333 parts per million per kelvin, at every mismatch on the slider, because the ratio is 1/T and contains nothing about the device at all.

semiconductors · Differential pair One diode curve, eight one-decade fits, and eight different ideality factors. computed by solving, not by drawing. A junction with two conduction mechanisms — recombination near n = 2 at low current, diffusion near n = 1 above it — and a series resistance, which is what a real diode is. Fitting ln(i) against v over each decade in turn returns an ideality factor for each, and they run from 1.227 to 1.984 without being monotonic: the factor rises through the recombination region, falls through the diffusion region, and rises again where the series resistance takes over. Two of the windows are straight to a few parts in a thousand, so the residual gives no warning. The bars are what each fit predicts for the forward voltage at 1 mA: the worst is out by -186 millivolts, which is a current 0.01 times the truth.

The constant that is a window

A diode's ideality factor is quoted as a number and defined as a derivative, which means it has a value at every current and no value anywhere. Eight one-decade fits to one curve return factors from 1.23 to 1.98, two of them straight to a few parts in a thousand — so the residual gives no warning at all. Asked for the forward voltage at a milliamp, the window containing it is right to a third of a millivolt and the worst is out by 186, which is a current a hundredth of the truth.

limits · Diode model Linearising an exponential at 125 °C, and what it costs. The linear model understates the gain by 1% at 9.69 mV and by 10% at 30.2 mV. The thermal voltage at this temperature is 34.3 mV, so "small compared with Vₜ" is not the criterion — 28% of Vₜ is already 1% wrong.

The edges that move with the room

Every boundary in this collection is quoted at one temperature and most of them are functions of it. The small-signal edge is proportional to the thermal voltage, so it runs from 5.67 millivolts at −40 degrees to 9.69 at +125 — a factor of 1.71, the ratio of the absolute temperatures exactly. A realised Q is 1.54 per cent high at one end of that range and 2.58 at the other. The numbers are right; the condition attached to them was left off, and it is the same condition every time.

limits · Model edges Two currents called saturation: one doubles every 4.49 K, the other every 8.98 K. computed by solving, not by drawing. The two current scales of one model junction against temperature, on a logarithmic axis. The saturation current of the exponential law goes as the square of the intrinsic carrier density — a cube of the temperature and the whole band gap in a Boltzmann factor — and doubles every 4.489 K at 300 K. The generation current a reverse-biased junction actually conducts goes as the density itself, with half the band gap, and doubles every 8.978 K: exactly twice as long, at every temperature. The dashed line is "doubles every ten kelvin" drawn through the generation scale, which is the current the rule belongs to. At 300 K this junction's two scales are 10 fA and 2 nA, which are its own parameters and not a property of silicon, and they become equal only at 616.8 K, or 343.6 °C.

Two currents with one name

A junction's saturation current is two currents with one name. The one in the forward law doubles every 4.49 kelvin; the one a reverse-biased junction actually conducts is generated in its depletion region, doubles every 8.98, and on this model junction is 3.06 × 10⁵ times larger at a volt of reverse bias. Doubles every ten kelvin is the second current's rule, and applied to the first it turns the forward drop's −1.81 millivolts per kelvin into +0.39.

limits · Diode model At 300 K one junction holds a logarithm to ±1% over 2.4 decades as a diode and 8.5 at its collector. computed by solving, not by drawing. The voltage of one model junction against the logarithm of the current it carries, as a percentage error of that current from a straight line fitted over the widest range that stays within ±1%. Taken as a diode — both mechanisms and 0.6 Ω of series resistance — the range is 2.40 decades, from 50.1 nA to 12.6 µA, and its slope is an ideality of 1.982. Taken at the collector, where the recombination current is supplied from the base and 1.604 Ω remains, it is 8.50 decades, from the axis's own end at 1 pA to 316 µA, at an ideality of 1.0001. Nothing arrives beside the collector current, so its lower end on this axis is the axis.

The logarithm is in the collector

A diode is the textbook logarithm, and a real junction holds one to within one per cent over only 2.40 decades — from 50 nanoamps to 12.6 microamps, at an ideality of 1.98 — because two mechanisms and a series resistance share its terminals. The same junction read at a transistor's collector, with its recombination current supplied from the base, holds 8.50 decades at an ideality of 1.0001. How far the logarithm reaches is decided by which terminal the current is taken from, and at the bottom of the range by a leakage current a millivolt is enough to switch on.

limits · Diode model The growth per cycle, and the form that is a fifth low at the top of the range. computed by solving, not by drawing. The factor the envelope is multiplied by each cycle, against the gain. The solid curve is exp(π(k−3)/√(1 − ((k−3)/2)²)), which is what the characteristic equation gives and what the netlist's own poles return to twelve digits; the dashed one is exp(π(k−3)), which drops the denominator. The circles are the marched envelope, fitted over the cycles that are still small — 80 of them at k = 3.01 and 4 at k = 3.2, and none at all above that. The two expressions differ by 3.9e-7 at k = 3.01 and by 20.462% at k = 3.8, so the approximation fails exactly where nothing is left to check it against.

Two exponentials, and where they meet

An oscillator's envelope grows by exp(π(k−3)/√(1 − ((k−3)/2)²)) a cycle, and the form usually quoted drops the denominator — exact to four parts in ten million at a hundredth above three, and 20.462 per cent low at 3.8, which is precisely where too few small cycles are left to measure it. Where the growth stops is the diode's own exponential: 108.5 millivolts of amplitude for every decade of saturation current, proportional to the ideality to four parts in a thousand. Above 60.121 nanoamperes the limiter is already conducting at zero signal and there is no oscillation at all.

applied · Oscillator The step at which the output impedance stops being a number. computed by solving, not by drawing. The excursion divided by the step, against the step. The flat line is the linear model, and it is flat to 0.0 parts per million across four decades — which is what an impedance is. The rising curve is the same netlist with the differential pair's tanh in the transconductor, and it leaves at 10.6 mA: the input error there is 3.63 thermal voltages, so the boundary is an amplitude in the pair's own units rather than a current with the amplifier's name on it. At 300 mA the ratio is 54.5 Ω against the linear 23.6 — 131 per cent, and it is no longer a property of the circuit at all. The slew rate that decides it is 3.25 V/µs, which is twice the thermal voltage times the gain-bandwidth in radians, and contains no design choice.

The step too large to have an impedance

The rung below drove the load node with a current step and reported an impedance: a voltage divided by a current, which is a number only if the ratio does not depend on the current. Give the amplifier the differential pair's own tanh in place of a linear transconductor and it is a number up to 10.6 milliamps and not above — where the input error is 3.63 thermal voltages, and where the slew rate that decides it is twice the thermal voltage times the gain-bandwidth in radians, containing no design choice at all.

feedback · Capacitive load A junction's noise against its own resistance's: exactly one at zero volts, and a half only far from it. computed by solving, not by drawing. A junction carries two currents at once, Is·e^(V/nVt) forwards and Is backwards, and each has its own shot noise. Their noise over the Johnson noise of the junction's own conductance is n(1 + e^−u)/2. At n = 1 it is 1.000000 at zero volts, 0.5676 at 50 mV, within one per cent of 0.50 only above 115.1 mV — where the forward current is ninety-nine saturation currents — and 2.978 at −40.00 mV of reverse bias. The half the forward-biased junction is known for is the limit of this curve, not its value.

The junction that is a resistor at zero volts

A forward-biased junction makes half the noise power of a resistor of its own dynamic resistance, and that half is a limit rather than a value. Kept with the saturation current that flows backwards across it, the ratio is one exactly at zero volts, 0.5676 at 50 millivolts, and within one per cent of the half only above 115.1 — at ninety-nine saturation currents, which is a picoampere on a small silicon diode and a microampere on a leaky one. A photodiode held at zero volts has the Johnson noise of its shunt resistance and nothing else, and it becomes shot-noise-limited at 49.981 millivolts of photocurrent drop.

noise · Shot noise A junction and its resistor in one loop: equal shares at 12.50 mV, and quietest against both at 49.98 mV. computed by solving, not by drawing. A junction carrying 25 µA in series with a resistor, the loop closed into a short and solved as a netlist with each noise current injected across its own element. Against the drop across the resistor: the bare junction's 2qI, the bare resistor's 4kT/R, each one's share of what reaches the outside, and the total. The shares are equal at 12.50 mV (500 Ω), not at the 49.98 mV where the bare floors cross; there the resistor supplies 80.0 per cent and the total is 0.5556 of either floor. The total is below both floors at every drop.

The resistor in the same loop

A resistor's noise and a junction's are equal as bare densities at 49.98 millivolts of drop, and a junction in series with the resistor that carries its current is the arrangement every current source is built from. In one loop each noise current has to cross the other element, so the two supply equal shares at 12.50 millivolts, a quarter of the crossing; at the crossing itself the resistor supplies 80 per cent and the loop is 2.553 decibels below both floors, which is further than it gets anywhere else. The same resistor multiplies the stage's input-referred noise by five.

noise · Shot noise A transistor's two noise generators are one current: their product is 0.8008 nV·pA/Hz at every bias. computed by solving, not by drawing. The input voltage noise of a bipolar stage, √(2kT·rₑ), is its collector current's shot noise referred through gₘ, and falls as the current rises; its input current noise, √(2qI_C/β), is its base current's, and rises. At β = 100 their product is 2kT/√β = 0.8008 nV·pA/Hz at every collector current from a microampere to ten milliamps, so the best noise figure, 0.4139 dB, does not depend on the bias. What does is where it is: the optimum source resistance times the current is √β·Vt = 249.9 mV, and the two lines cross where that resistance is a kilohm, at 250 µA.

The two generators that are one current

An amplifier's noise is two generators, a voltage in series with its input and a current across it, and the essays on its noise figure treat them as independent numbers. In a bipolar input stage they are one current's shot noise divided two ways, by the collector and the base, and their product is 2kT/√β at every collector current: 0.8008 nV·pA per hertz at a current gain of a hundred, from a microampere to ten milliamps. The best noise figure, 0.4139 dB, does not depend on the bias. The bias decides only where the best source is, and 50 ohms of base resistance decides what the best actually is below 500.

noise · Shot noise Two large-signal limits, each alone and then both, at 20 mA and half of it. computed by solving, not by drawing. Four marches of one netlist at each load: neither limit, the input pair's tanh alone, the output stage's 20 mA alone, and both, driven by a 10 mA step. The three curves are each limit's departure from the linear march and the departure with both present; the faint line is the two singles added. Both lies on the sum and a little above it — 1.112 times it at 0.47 nF and 1.022 at 47 nF — so the limits are present together rather than taking turns. Where the two singles cross, near 10 nanofarads, the pair costs 1.88 times what the worse of them costs alone.

The load that neither limit owns

Nine rungs of this argument asked which of an amplifier's two large-signal limits binds, and drew the load capacitance where the answer changes hands. Both are present at every load: the excursion with both in the netlist is the two departures added and between 2 and 12 per cent more, never the larger of them. So the crossing is not a handover but a maximum — at 12 nanofarads the pair costs 2.084 times what the worse of them costs alone, against 1.35 at 2.2 nanofarads and 1.07 at 47 — and the same peak sits on the resistance axis at 20 ohms and the gain-bandwidth axis at 50 megahertz.

feedback · Capacitive load One output in saturation takes 6.5% off another that is at five volts. computed by solving, not by drawing. A three-transistor mirror: a reference, an output taken down into saturation, and a third output held at five volts throughout. The upper curve is the saturating output's own loss and the lower one is the sibling's. At 50 mV the saturating output is 27.3 per cent down and the sibling, which is nowhere near saturation, is 6.54 per cent down. The reference current moves by -0.0188 per cent, which is nothing: a base current is a hundred and fiftieth of a collector current and the reference is set by a resistor from the supply. What does move is the base-emitter voltage every output shares — by -1.75 millivolts — and every output is an exponential of it.

The refusal, and what it was protecting

A current mirror's model has declined to answer below two hundred millivolts of collector-emitter voltage since it was written, because it has no base-collector junction and would return a forward-active current for a saturated transistor. Put the junction in and the refusal turns out to have been placed where the model it protects is still right to seven parts in ten thousand — and the mirror's real failure is somewhere else entirely: a saturated output takes six and a half per cent off an output that is sitting at five volts.

semiconductors · Current mirror A half-decibel filter that meets one decibel at 25 °C and does not at 89. computed by solving, not by drawing. The passband ripple of a fifth-order 0.5 dB Chebyshev built from three Sallen–Key sections, against temperature, with a part whose gain-bandwidth at 300 K is 300 kHz against a 1 kHz corner. Not one passive component has a temperature coefficient in this model. The ripple is 0.824 dB at −40 °C and 1.049 at +125, and it crosses a one-decibel specification at 88.6 °C — a boundary in temperature, which every other edge in this collection is not. The dashed line is the same filter with a tail current proportional to absolute temperature: 0.916 dB at both ends, and no crossing anywhere.

The ripple that is a temperature

The rung below found that an amplifier a hundred times the corner leaves a section's quality factor two per cent high. That two per cent has a temperature in it: with a tail current a resistor sets, the transconductance falls as one over absolute temperature, and a fifth-order half-decibel design whose passives have no temperature coefficient at all goes from 0.82 decibels of ripple at minus forty to 1.05 at a hundred and twenty-five — crossing a one-decibel specification at 89 °C. With the other bias it does not move at all.

filters · Q enhancement Three amplitudes, all of them "one per cent wrong". computed by solving, not by drawing. An exponential driven by a sinusoid has I₀(a) as its mean, 2I₁(a) as its fundamental and 2Iₙ(a) as its harmonics, all checked here against a numerical transform of the waveform itself, agreeing to 9.0e-11. Each gives a different one-per-cent boundary at 27 °C: 1.03 mV for the second harmonic, 5.17 mV for the shift in the operating point the model was linearised about, and 7.30 mV for the gain — which is 1 : 5 : 5√2 at this criterion, and the largest of them is the one usually quoted. The spacing is not a property of the device: the second harmonic is first order in the amplitude and the other two are second, so tightening the criterion to a part in ten thousand spreads the same three to 1 : 50.0 : 70.71. At a drive of one thermal voltage the bias current is 26.6% above quiescent, which is the boundary nobody counts because it moves the thing the model was built at rather than what the model predicts.

Three amplitudes, all of them one per cent

The amplitude at which linearising an exponential is one per cent wrong is 7.30 mV, and that is a statement about the gain. Two other quantities are also one per cent wrong somewhere: the second harmonic reaches one per cent at 1.03 mV and the shift in the operating point the model was linearised about reaches it at 5.17 — which is √2 below the gain boundary exactly, because the mean goes as a²/4 and the fundamental as a²/8. And the spacing is not a property of the device: tighten the criterion to a part in ten thousand and the same three spread to 1 : 50 : 70.7.

limits · Small-signal A diode thermometer measuring its own sense current, at 600 K/W. computed by solving, not by drawing. The same fixed point as the core and the thermistor, on a junction: the dissipation is I·V and V falls with temperature, so the loop gain is negative and the equation has one root at every current. What it costs is two errors. The junction sits above ambient by 0.29 millikelvin at a microamp and 4.26 kelvin at ten milliamperes, which a calibration removes; and a kelvin of ambient produces less than a kelvin of junction, by 1/(1 − R_th·dP/dT), which it does not. After a calibration at 25 degrees the reading at 85 is out by -583 millikelvin at ten milliamperes and -0.09 at a microamp. The coefficient itself moves too — -2.403 against -1.613 millivolts a kelvin — so a quoted tempco carries a sense current as well as a junction.

The sensor inside its own answer

A junction driven from a current source cannot run away, because its forward voltage falls with temperature and its loop gain is therefore negative. What that costs is a thermometer that is warmer than what it is measuring by 4.26 kelvin at ten milliamperes, and — the part a calibration cannot remove — under-reports every change in ambient by 9,584 parts per million, because the sense current's own dissipation falls as the reading rises. Calibrated at 25 degrees, it is out by 583 millikelvin at 85.

semiconductors · Thermal feedback What a pair does to the three boundaries: removes two, moves one. computed by solving, not by drawing, with every harmonic taken from a transform of the waveform rather than from a series. A differential pair's transfer is an odd function, so the mean and every even harmonic are zero — -3.2e-17 and 9.1e-17 at a drive of two thermal voltages, which is absent rather than small. Two of the three one-per-cent boundaries therefore do not exist for a pair at all. The third, the loss of gain, moves by √2 in the limit of a tight criterion and by 1.42610 at the one per cent quoted here — 10.42 mV against 7.304 mV at 27 °C, against √2 = 1.41421 and 1.41433 at a criterion a hundred times tighter. So a pair reached for as headroom has bought forty per cent of it and a pair reached for as linearity has bought something else entirely. Twenty millivolts of imbalance brings the even orders straight back, which is what says the cancellation belongs to the symmetry rather than to the topology.

Two boundaries removed, and one moved

A differential pair's transfer is odd, so its mean and every even harmonic are zero — −3.2×10⁻¹⁷ and 9.1×10⁻¹⁷ at a drive of two thermal voltages, absent rather than small. Two of the three one-per-cent boundaries therefore do not exist for a pair at all. The third, the loss of gain, moves by √2 in the limit and by 1.42610 at the one per cent usually quoted: 10.42 mV against 7.304. So a pair reached for as headroom has bought forty per cent of it, and twenty millivolts of imbalance brings the even orders straight back.

limits · Small-signal Three mismatches, and only one of them reaches the output. computed by solving, not by drawing. Each of the three quantities that can differ between the two transistors is given a spread of its own, one at a time, and 200 pairs are solved at each. The saturation currents produce a spread that follows them exactly — exponent 0.998, so 1.910 per cent of copy error for two per cent of mismatch. The current gains produce a line of slope 2.003, which is second order rather than first, and land at 2.20e-4 per cent for the same two. There is no third line because there is no third component: with no emitter resistors there is nothing for a resistor tolerance to be a tolerance of, and matching a mirror is a statement about emitter area and about nothing else.

The mismatch that cancels itself

A current mirror's copy error is spread by three things the two transistors can differ in, and the population that measures it has always drawn all three at once. Turned on one at a time, a two per cent spread of saturation currents gives 1.910 per cent of copy error and a two per cent spread of current gains gives 0.00022 — because the gains enter only as a sum of reciprocals, which has no first derivative where they are equal. Then the standard cure un-cancels it, by a factor of 86.

semiconductors · Current mirror

Named alongside it

The objects these essays reach for when they reach for this one.

Model rangeSaturation currentOperating pointTemperature coefficientIdeality factorMeasurement conditionTransconductanceCurrent noiseDesign tradeoffDynamic resistanceLinearisationShot noise

All concepts