Circuit Response
every model has an edge, and the figure carries it
Concept

Transimpedance — where it appears

A gain from an input current to an output voltage, which is what a photodiode amplifier provides. Its bandwidth is set by the feedback resistor against the total capacitance at the summing node — the diode's, the amplifier's own and the feedback capacitor's — rather than by the amplifier alone.

Named by 5 essays across 2 fields — each of them below, with the objects they name alongside it.

A photodiode's own capacitance sets the bandwidth, as its -0.50 power. computed by solving, not by drawing. The bandwidth of a 1.0 MΩ transimpedance stage against the capacitance of the diode driving it, with the feedback capacitor at each point bisected to give exactly forty-five degrees of phase margin on the solved loop. The classical expression √(GBW/2π·rf·cd) is drawn over it: the right shape, and conservative by about a fifth at every capacitance. The bandwidth falls as the -0.497 power of the capacitance — a square-root law, so a diode of four times the area costs half the bandwidth rather than three quarters of it. At 30 pF the compensation is 0.598 pF against the expression's 0.725, and the bandwidth 295 kHz against 220.

Where the trouble is at the input

Every other arrangement in this field has its difficulty at the output — a capacitive load, an isolation resistor, a load that draws current. A photodiode amplifier has it at the input, and the capacitance causing it is not a parasitic: it is the diode's junction, which is the price of its area, and area is what a photodiode is bought for. The feedback resistor's own noise is 127 nV/√Hz against the amplifier's 4, and the amplifier is still ninety-five per cent of the noise at a large diode.

feedback · Transimpedance A junction's noise against its own resistance's: exactly one at zero volts, and a half only far from it. computed by solving, not by drawing. A junction carries two currents at once, Is·e^(V/nVt) forwards and Is backwards, and each has its own shot noise. Their noise over the Johnson noise of the junction's own conductance is n(1 + e^−u)/2. At n = 1 it is 1.000000 at zero volts, 0.5676 at 50 mV, within one per cent of 0.50 only above 115.1 mV — where the forward current is ninety-nine saturation currents — and 2.978 at −40.00 mV of reverse bias. The half the forward-biased junction is known for is the limit of this curve, not its value.

The junction that is a resistor at zero volts

A forward-biased junction makes half the noise power of a resistor of its own dynamic resistance, and that half is a limit rather than a value. Kept with the saturation current that flows backwards across it, the ratio is one exactly at zero volts, 0.5676 at 50 millivolts, and within one per cent of the half only above 115.1 — at ninety-nine saturation currents, which is a picoampere on a small silicon diode and a microampere on a leaky one. A photodiode held at zero volts has the Johnson noise of its shunt resistance and nothing else, and it becomes shot-noise-limited at 49.981 millivolts of photocurrent drop.

noise · Shot noise One capacitor moves three quantities, and the expression's own answer peaks by 1.18 dB. computed by solving, not by drawing. The bandwidth, the peaking and the total output noise of a 1.0 MΩ transimpedance stage against its feedback capacitor, swept from 0.30 to 4.20 times what the classical expression asks for. Over that factor of fourteen the bandwidth falls from 334 to 55.4 kHz, the total noise from 230 to 65 µV, and the peaking from 10.0 dB to nothing. The expression's own answer sits at 1.18 dB of peaking, 0.82× is where the loop reaches forty-five degrees, and √2× is where the response is flat — so the choice usually quoted as maximally flat is neither of the two conditions it is quoted for. The faint families are the same three quantities at 3 pF and 300 pF of diode: normalised this way they are one curve, so the diode sets the scale and the multiple sets the shape.

The factor the expression leaves out

The classical compensation for a photodiode amplifier is quoted both as the forty-five degree choice and as the maximally flat one, and it is neither: it leaves 1.18 dB of peaking and 52.4° of margin. Flat is at exactly √2 times it — fitted at 1.4186 against 1.4142, at every detector from 3 pF to 1 nF. And the third quantity the capacitor is supposed to trade, the noise, does not move at all inside the signal band: three compensations spanning a factor of fourteen give 8.37 against 8.36 µV in a 4.36 kHz measurement and 230 against 65 µV over the whole plane.

feedback · Transimpedance The direct-current error a bigger feedback resistor does not fix. computed by solving, not by drawing, at direct current with the amplifier in the netlist. A 1.0 nA photocurrent into 100 MΩ gives -0.100 V. The bias current flows in the same resistor, so its contribution is the ratio of the two currents — 0.1000% at 25 °C, and the same percentage at 1 MΩ and at 1 GΩ, which is checked by changing the resistor rather than by reading an expression. The amplifier's 100 µV of offset behaves the other way: it is multiplied by one plus the resistor over the diode's own leakage, so it grows with the resistor and with temperature. Both terms double every ten kelvin, for two different reasons, and at 85 °C they are 6.40% and 0.740% against 0.100% and 0.110% at 25.

The error a bigger resistor cannot help

Every other quantity in a photodiode amplifier improves with a larger feedback resistor: the signal grows as R and the resistor's own noise as √R, so the ratio goes as √R. The bias current does not behave like either — it flows in the same resistor the signal does, so its contribution is the ratio of the two currents with the resistance cancelled, 0.1 per cent at 25 °C and the same 0.1 per cent at a megohm and at a gigohm. The offset behaves the other way, growing as one plus the resistor over the diode's own leakage, and at 85 °C the two are 6.40 and 0.74 per cent against 0.10 and 0.11 at room temperature.

feedback · Transimpedance What a feedback tee buys, and the single thing it charges. computed by solving, not by drawing. Two 50 kΩ resistors with a 6.250 kΩ tap give 500.0 kΩ of transimpedance, which is R₁(1 + R₂/R₃) + R₂ solved on the netlist. That expression has no term for the noise gain, and the tap sets it to 1 + R₁/R₃ = ×9.00 — against exactly one for a single resistor of any value, because at direct current the source is a capacitor. One quantity then does all three things at once. The signal and R₁'s own noise are multiplied together, so the tee buys no signal-to-noise ratio at all: 1846 against 5582 in a hertz at a nanoamp for one resistor of the same transimpedance, a factor of 3.02 which is the square root of the noise gain. The amplifier's own voltage noise and offset are multiplied where they were not before. And the phase margin RISES, from 1.8° to 15.9°, because starting the noise gain high shortens its climb to the peak — so the tee is a compensation that charges for itself in noise, and a capacitor across the feedback is the same compensation for nothing. With no tap the three effects are absent rather than small.

The tee that charges for its own compensation

A feedback tee makes a large transimpedance out of small resistors, and R₁(1 + R₂/R₃) + R₂ is the whole of what is usually said about it. The expression has no term for the noise gain, and the tap sets that to 1 + R₁/R₃ — nine, where a single feedback resistor of any value gives exactly one, because at direct current the source is a capacitor. One quantity then does everything: the signal and R₁'s own noise are multiplied together so the tee buys no signal-to-noise ratio at all, and the phase margin RISES from 1.8° to 15.9°.

feedback · Transimpedance

Named alongside it

The objects these essays reach for when they reach for this one.

Design tradeoffJohnson noiseModel rangeNoise gainPhase marginSignal-to-noise ratioAnti-alias filterClosed formCompensation networkCurrent noiseDark currentDynamic resistance

All concepts