Circuit Response
every model has an edge, and the figure carries it
Concept

Bulk resistance — where it appears

The resistance of the semiconductor and contacts between a junction and its terminals, which adds a voltage proportional to the current. It dominates a diode's slope at high current, a fit with no term for it reads it as a larger ideality factor, and a forward curve taken slowly hides part of it behind the junction's own heating.

Named by 4 essays across one field — each of them below, with the objects they name alongside it.

One diode curve, eight one-decade fits, and eight different ideality factors. computed by solving, not by drawing. A junction with two conduction mechanisms — recombination near n = 2 at low current, diffusion near n = 1 above it — and a series resistance, which is what a real diode is. Fitting ln(i) against v over each decade in turn returns an ideality factor for each, and they run from 1.227 to 1.984 without being monotonic: the factor rises through the recombination region, falls through the diffusion region, and rises again where the series resistance takes over. Two of the windows are straight to a few parts in a thousand, so the residual gives no warning. The bars are what each fit predicts for the forward voltage at 1 mA: the worst is out by -186 millivolts, which is a current 0.01 times the truth.

The constant that is a window

A diode's ideality factor is quoted as a number and defined as a derivative, which means it has a value at every current and no value anywhere. Eight one-decade fits to one curve return factors from 1.23 to 1.98, two of them straight to a few parts in a thousand — so the residual gives no warning at all. Asked for the forward voltage at a milliamp, the window containing it is right to a third of a millivolt and the worst is out by 186, which is a current a hundredth of the truth.

limits · Diode model A fit to the held curve reads the series resistance falling to nothing at 532 K/W. computed by solving, not by drawing. Each point is a three-parameter fit — a constant, an ideality factor and a series resistance — to the held forward curve between 10 and 100 mA, for a junction built with 0.6 Ω and no temperature coefficient on it, mounted at the thermal resistance on the axis. With no thermal resistance the fit returns 0.580 Ω with a residual of 43.9 µV. At 350 K/W it returns 0.184 Ω, an ideality of 1.086 and a residual of 34.0 µV. The resistance it reports reaches zero at 531.7 K/W and is negative beyond.

The resistance a slow curve cannot see

A diode's series resistance is read off the top of its forward curve, and a bench curve is a slow one: each point is held until the junction has warmed to it. Through 350 kelvin per watt the held curve sits 39.7 millivolts below the pulsed one at 100 milliamps, and the three-parameter fit that reads 0.580 ohms from the pulsed curve reads 0.184 from the held one — with a smaller residual. The fitted resistance reaches zero at 531.7 kelvin per watt, and the resistance it hid is what keeps the junction from folding back: with 0.05 ohms instead of 0.6 the held curve turns over at 87.6 milliamps.

limits · Diode model At 300 K one junction holds a logarithm to ±1% over 2.4 decades as a diode and 8.5 at its collector. computed by solving, not by drawing. The voltage of one model junction against the logarithm of the current it carries, as a percentage error of that current from a straight line fitted over the widest range that stays within ±1%. Taken as a diode — both mechanisms and 0.6 Ω of series resistance — the range is 2.40 decades, from 50.1 nA to 12.6 µA, and its slope is an ideality of 1.982. Taken at the collector, where the recombination current is supplied from the base and 1.604 Ω remains, it is 8.50 decades, from the axis's own end at 1 pA to 316 µA, at an ideality of 1.0001. Nothing arrives beside the collector current, so its lower end on this axis is the axis.

The logarithm is in the collector

A diode is the textbook logarithm, and a real junction holds one to within one per cent over only 2.40 decades — from 50 nanoamps to 12.6 microamps, at an ideality of 1.98 — because two mechanisms and a series resistance share its terminals. The same junction read at a transistor's collector, with its recombination current supplied from the base, holds 8.50 decades at an ideality of 1.0001. How far the logarithm reaches is decided by which terminal the current is taken from, and at the bottom of the range by a leakage current a millivolt is enough to switch on.

limits · Diode model Over one decade a constant is out by ±29.76 mV and a drop plus a resistance by ±8.002 mV. computed by solving, not by drawing. The forward drop of a pure exponential junction over the decade from 1e-3 to 1e-2 amperes, with the best constant drop and the best drop-plus-resistance drawn across it. Both are fitted minimax — the model whose WORST error over the window is smallest, which is what a design has to tolerate — rather than by least squares. The constant is 684.6 mV and is out by ±29.76 mV; the line is 656.2 mV plus 6.61 Ω and is out by ±8.002 mV, which is 3.72 times better. The best constant needs no search: it is the midpoint of the window's highest and lowest voltage, and its error is half their difference.

The straight line between two models

Between a constant seven-tenths of a volt and an exponential sits the model a designer actually reaches for: a drop plus a resistance. Fitted so that its worst error over a decade of current is as small as it can be, it is out by ±8.00 millivolts where the best constant is out by ±29.76 — and both numbers are the same over every decade, because a decade of a logarithm is the same shape wherever it is taken. On a real two-mechanism junction the line does best in the top decade, ±8.71 against a constant's ±58.53, because a series resistance is exactly the term the line has and the constant has none. And the resistance the fit returns is the part's plus 701 milliohms that is not there.

limits · Diode model

Named alongside it

The objects these essays reach for when they reach for this one.

Ideality factorMeasurement conditionModel rangeOperating pointDynamic resistanceLinearisationSaturation currentThermal voltageDesign tradeoffLeakage currentLoop gainPower law fit

All concepts