Concept

Mutual capacitance — where it appears

The capacitance between two conductors, carrying a current proportional to the rate of change of the voltage difference across it. On a coupled pair it is quoted as a fraction of the total capacitance to ground, and it sets how much of one track's signal appears on its neighbour.

Named by 4 essays across one field — each of them below, with the objects they name alongside it.

Two tracks, and a far end that cancels exactly when the field is all in one material. computed by solving, not by drawing, on 12 coupled sections of a 100 mm pair terminated in 50 Ω at all four ends. A mutual capacitance injects a current proportional to dV/dt and splits it towards both ends of the quiet track; a mutual inductance injects a voltage proportional to dI/dt and drives the two ends in opposite directions. So the near end goes as Cm/Ct + Lm/Lt and the far end as their difference, with the same constant in front of both — measured here as 1.048e-2 either way, over a slider that moves the ratio by five times. The consequence is that the far end is not a smaller effect but a cancellation: at a ratio of one it is 7.52e-19 of the drive, which is zero to the last bits of a double, while the near end is 1.048e-3. That is why a stripline has no far-end crosstalk and a microstrip has some — what shows up there measures the field that is in air, not the spacing. The model is lumped and stops where it says: a section is one degree long at 50.0 MHz.

The far end that cancels

Two mechanisms couple two parallel tracks: a mutual capacitance injecting a current and a mutual inductance injecting a voltage. They add at the near end of the quiet track and subtract at the far end, with the same constant in front of both — measured here as 1.048 times ten to the minus two either way, across a slider that moves their ratio by five times. So the far end is not a smaller effect: when the two couplings are equal it is 3.5 times ten to the minus nineteen of the drive, which is zero to the last bits of a double.

lines · Crosstalk

The null is a V and not a bowl: one per cent of ratio error is 5.0e-3 of the near end. computed by solving, not by drawing. The same twelve coupled sections read at 10.0 MHz, with the ratio of the two couplings swept across the null rather than sat at one setting. The far end divided by the near end is |1 − r|/(1 + r) at every point — a straight-sided V through zero, first order in the departure with a coefficient of one half, and not a rounded minimum with a flat bottom. So there is no tolerance band: a ratio one per cent off gives 4.98e-3 of the near end and ten per cent off gives 4.76e-2, and the exchange rate between them is fixed. The upper trace is the near end over the same sweep, which moves by 11 per cent while the lower one moves through 14 decades — the two ends are the same coupling read as a sum and as a difference, which is why one of them has a zero in it and the other cannot.

How wide a null is

A far end at 3.5×10⁻¹⁹ of the drive is a statement about arithmetic until somebody asks how far the two couplings may differ before it comes back. The answer has no flat bottom in it: the far end divided by the near end is |1−r|/(1+r) exactly, so the null is a V and a ratio one per cent off returns 4.98×10⁻³ of the near end. On the axis a board is built to that is a difference of 0.0081 between the two modes' effective permittivities, out of 3.99 — two parts in a thousand, and 0.675 picoseconds of mode skew over a hundred millimetres.

lines · Crosstalk

Near-end crosstalk from a 200 ps edge, 100 mm of coupled track against 10 mm. computed by solving, not by drawing, the pair solved mode by mode and returned to time from its harmonics. Over 100 mm the near end rises with the edge, holds a plateau of 12.51 mV per volt for twice the line's delay, 1.33 ns, and falls. Over 10 mm the round trip is shorter than the edge and the pulse never reaches the plateau: 8.34 mV. The plateau is Kb, a quarter of the sum of the two couplings, on the 0.5 V the driven line carries: 12.50 mV.

The near end that stops growing

Near-end crosstalk is a length only until the coupled run's round trip equals the edge's rise time; past that it is a constant. Solved mode by mode and returned to time, a 200 ps edge on 100 mm of coupled track gives a plateau of 12.51 mV per volt — Kb, a quarter of the sum of the two couplings, on the driven line's half-volt — held for the 1.33 ns round trip. The knee is at v·tr/2: 7 mm for a 100 ps edge, 75 mm for 1 ns. Past it a longer run adds width and not height, and the pulse's area keeps growing as Kb times the round trip.

lines · Crosstalk

Both ends of the quiet line, 100 mm of microstrip-like coupling, edge 200 ps. computed by solving, not by drawing. The near end (pale) is the saturated plateau, 16.28 mV per volt. The far end (dark) is a single pulse arriving with the edge after one delay, 0.676 ns, as wide as the edge and 25.16 mV per volt deep — negative, because the inductive coupling exceeds the capacitive. Its depth is the coupling difference, the delay and the edge's slope multiplied: 24.96 predicted.

The far end that is a derivative

Where the two couplings are unequal the far end does not cancel, and in time it is the derivative of the edge: a single pulse as wide as the rise time, arriving after one delay, its height the coupling difference times the delay times the edge's slope. On 100 mm of microstrip-like coupling a 200 ps edge gives −25.16 mV per volt against 24.96 predicted, and the height falls as one over the rise time with a fitted slope of −1.000 while the saturated near end sits still. It grows with length without a knee until the two modes separate by a whole edge — 249 mm for a 50 ps edge — and then stops at half the driven line's voltage.

lines · Crosstalk

Named alongside it

The objects these essays reach for when they reach for this one.

Crosstalk Mutual inductance Transmission line Homogeneous dielectric Lumped approximation Model range Propagation delay Rise time Characteristic impedance Design tradeoff Electrical length Mode conversion

All concepts