Circuit Response
every model has an edge, and the figure carries it
Concept

Series-pass regulator — where it appears

A supply that holds its output steady by controlling a device in series with the load, driven by an amplifier comparing that output against a reference. It is a voltage source below the loop's bandwidth and a capacitor above it, and the frequency where it changes hands is a property of the loop.

Named by 5 essays across one field — each of them below, with the objects they name alongside it.

A five-volt regulator's output impedance, with 1.00 Ω of series resistance. 0.430 mΩ at direct current, 1.95 Ω at 10.0 kHz — a factor of 4.52e+3 — and it has already doubled by 4.81 Hz. The upper curve is the same circuit with its loop opened, and the ratio between them is the loop gain. A regulator is a voltage source below a frequency and the datasheet's milliohms are the value at the bottom of it.

A source below a frequency

A five-volt regulator's output impedance is 0.43 milliohms, which is the number a datasheet quotes. It has doubled by 4.8 hertz, is ten times worse by 27, and reaches 1.95 ohms at ten kilohertz — four and a half thousand times its own specification, and higher there than the same circuit with its feedback loop cut. Two routes to that curve, sharing only the netlist, agree to a part in ten to the thirteenth.

applied · Regulator The window a 10 µF capacitor leaves. Above 939 mΩ the loop holds 45° of margin; below it the regulator rings and then oscillates. The droop after a 100 mA step is smallest at 817 mΩ — 129 mV — and by 19.9 Ω it is 1.468 V, because at the first instant of a step the capacitor cannot move and the whole step falls across its series resistance. Two requirements, opposite directions, and the useful values are between them.

Two requirements pulling one capacitor

The output capacitor's series resistance is a stability requirement and a transient requirement at once, and they pull it in opposite directions. Below 939 milliohms this loop has less than 45 degrees of margin; above about 850 the droop after a load step starts to grow, because at the first instant of a step the capacitor cannot move and the whole step falls across that resistance. The droop is smallest 10 per cent inside the unstable region, which means the best transient this design can have is one it must not be built with.

applied · Regulator Rejection is not a property of the loop. The same regulator with the same loop gain and the same 46.5° of phase margin, drawn twice. With the amplifier's output referred to ground the rail reaches the output at -67.3 dB at the bottom and 5.79 dB at 10.0 kHz — where it is amplified. Referred to the rail instead, every point is 60.00 dB lower, which is 20 log(gm·ro) for the pass device and not a design choice.

What gets through from the rail

A regulator's job is to hold its output still while its input moves, and the measurement says it does that well at ten hertz, badly at a kilohertz, and not at all at ten kilohertz — where this one puts out 1.9 times what arrives. Then the same netlist with one node moved, the same loop gain and the same 46.5 degrees of margin, rejects 60.009 decibels better at every frequency in six decades. The sixty decibels is the pass device's own intrinsic gain and it is not a design choice.

applied · Regulator The ripple 1000 µF leaves, through the regulator: 60.62 mV rather than 21.11 mV. One settled cycle of the reservoir's output — 1.331 V peak to peak across 1000 µF — split into 1000 Fourier lines, each passed through the solved regulator's rail-to-output response, and summed. The output is 60.62 mV peak to peak. The ripple times the rejection at 100 Hz, -36.00 dB, gives 21.11 mV, which is 2.872 times too little: the rejection worsens at twenty decibels a decade, so each harmonic of the sawtooth arrives at nearly the size of the first. The 100 Hz line carries 23.4% of the output's mean square and the lines above 1 kHz 10.4%; the first three arrive at 7.731 mV at 100 Hz, 7.200 mV at 200 Hz, 6.388 mV at 300 Hz. The dashed curve is the 100 Hz line alone.

The ripple that arrives as a comb

The rejection essay multiplied two numbers: 1.331 volts of reservoir ripple and the regulator's 36.0 decibels of rejection at a hundred hertz, for 21 millivolts at the output. The ripple is a sawtooth, a comb of lines at every multiple of a hundred hertz, and the rejection worsens at twenty decibels a decade — so the second line arrives at nearly the size of the first, and the third too. Summed with their phases, the output is 60.62 millivolts, 2.87 times the estimate, and the hundred-hertz line carries only 23.4 per cent of it. A reservoir twenty-one times larger cuts the rail's ripple 14.8 times and the regulated ripple 5.95.

applied · Regulator The capacitor across the upper resistor: 90.9° of margin at 836.5 pF, and less ripple past it. The regulator's phase margin against a capacitor across the upper divider resistor, with the output ripple the 1000 µF reservoir leaves beside it. With no capacitor the margin is 46.47° at a crossover of 9.73 kHz, the output impedance at 10 kHz is 1.95 Ω, the worst rail rejection is 5.79 dB and the ripple 60.62 mV. The margin is greatest, 90.929°, at 836.5 pF — a zero at 6.34 kHz and a pole at 25.4 kHz around a crossover moved to 16.9 kHz — where the output impedance at 10 kHz is 828 mΩ, the worst rail rejection -1.50 dB and the ripple 52.33 mV. At 10 nF the margin has fallen back to 66.34° and the ripple is 35.40 mV.

The capacitor across the upper resistor

The rejection essay said a regulator reproduces its reference times its divider's four, and that a capacitor across the lower divider resistor brings that down to one at high frequency. Measured, the loop peaks the reference's gain to 5.68 near its crossover before any capacitor is added; a nanofarad across the lower resistor raises the peak to 11.2; and the capacitor that brings it down belongs across the upper resistor, where a nanofarad keeps the gain from ever exceeding four. The same capacitor is a lead pair in the loop: 836.5 picofarads takes the phase margin from 46.5 to 90.9 degrees, and ten nanofarads, past that optimum, still holds 66 while cutting the output ripple from 60.6 millivolts to 35.4.

applied · Regulator

Named alongside it

The objects these essays reach for when they reach for this one.

Loop gainDesign tradeoffPower supply rejectionOutput impedancePhase marginConduction angleEquivalent series resistanceFeedforwardIdeal voltage sourceIntrinsic gainLead compensationLoad regulation

All concepts